diff mbox series

[net-next,PATCHv6,1/2] dt-bindings: net: Add DT bindings for Socionext Netsec

Message ID 1504088752-6204-1-git-send-email-jaswinder.singh@linaro.org
State New
Headers show
Series net: ethernet: Socionext Netsec | expand

Commit Message

Jassi Brar Aug. 30, 2017, 10:25 a.m. UTC
This patch adds documentation for Device-Tree bindings for the
Socionext NetSec Controller driver.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

---
 .../devicetree/bindings/net/socionext-netsec.txt   | 46 ++++++++++++++++++++++
 1 file changed, 46 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/socionext-netsec.txt

-- 
2.7.4

Comments

Jassi Brar Aug. 31, 2017, 3:13 a.m. UTC | #1
On Wed, Aug 30, 2017 at 8:49 PM, Andrew Lunn <andrew@lunn.ch> wrote:
> On Wed, Aug 30, 2017 at 03:55:52PM +0530, Jassi Brar wrote:

>> This patch adds documentation for Device-Tree bindings for the

>> Socionext NetSec Controller driver.

>>

>> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

>> ---

>>  .../devicetree/bindings/net/socionext-netsec.txt   | 46 ++++++++++++++++++++++

>>  1 file changed, 46 insertions(+)

>>  create mode 100644 Documentation/devicetree/bindings/net/socionext-netsec.txt

>>

>> diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt

>> new file mode 100644

>> index 0000000..12d596c

>> --- /dev/null

>> +++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt

>> @@ -0,0 +1,46 @@

>> +* Socionext NetSec Ethernet Controller IP

>> +

>> +Required properties:

>> +- compatible: Should be "socionext,netsecv5"

>> +- reg: Address and length of the register sets, the first is the main

>> +     registers, then the rdlar and tdlar regions for the SoC

>> +- interrupts: Should contain ethernet controller interrupt

>> +- clocks: phandle to any clocks to be switched by runtime_pm

>> +- phy-mode: See ethernet.txt file in the same directory

>

>> +- max-speed: See ethernet.txt file in the same directory

>> +- max-frame-size: See ethernet.txt file in the same directory, if 9000 or

>> +     above jumbo frames are enabled

>> +- local-mac-address: See ethernet.txt file in the same directory

>

> These three are required, not optimal?

>

optional :)

>> +- phy-handle: phandle to select child phy

>> +

>> +Optional properties:

>> +- use-jumbo: Boolean property to suggest if jumbo packets should be used or not

>> +

>> +For the child phy

>> +

>> +- compatible "ethernet-phy-ieee802.3-c22" is needed

>

> This is normally considered optional. Why require it?

>

Yes, will do.

Thanks.
Rob Herring (Arm) Sept. 11, 2017, 8:37 p.m. UTC | #2
On Wed, Aug 30, 2017 at 03:55:52PM +0530, Jassi Brar wrote:
> This patch adds documentation for Device-Tree bindings for the

> Socionext NetSec Controller driver.

> 

> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>

> ---

>  .../devicetree/bindings/net/socionext-netsec.txt   | 46 ++++++++++++++++++++++

>  1 file changed, 46 insertions(+)

>  create mode 100644 Documentation/devicetree/bindings/net/socionext-netsec.txt

> 

> diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt

> new file mode 100644

> index 0000000..12d596c

> --- /dev/null

> +++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt

> @@ -0,0 +1,46 @@

> +* Socionext NetSec Ethernet Controller IP

> +

> +Required properties:

> +- compatible: Should be "socionext,netsecv5"


This should be SoC specific, or also have an SoC specific string.

> +- reg: Address and length of the register sets, the first is the main

> +	registers, then the rdlar and tdlar regions for the SoC

> +- interrupts: Should contain ethernet controller interrupt

> +- clocks: phandle to any clocks to be switched by runtime_pm

> +- phy-mode: See ethernet.txt file in the same directory

> +- max-speed: See ethernet.txt file in the same directory

> +- max-frame-size: See ethernet.txt file in the same directory, if 9000 or

> +	above jumbo frames are enabled

> +- local-mac-address: See ethernet.txt file in the same directory

> +- phy-handle: phandle to select child phy

> +

> +Optional properties:

> +- use-jumbo: Boolean property to suggest if jumbo packets should be used or not


Is this common or vendor specific. The former should refer to a common 
doc. The latter should have a vendor prefix. I'd think the former makes 
sense here.

But then why do you need this and max-frame-size?

> +

> +For the child phy

> +

> +- compatible "ethernet-phy-ieee802.3-c22" is needed

> +- device_type "ethernet-phy"

> +- reg: phy address

> +

> +

> +Example:

> +	eth0: ethernet {

> +		compatible = "socionext,netsecv5";

> +		reg = <0 0x31600000 0x10000>, <0 0x31618000 0x4000>, <0 0x3161c000 0x4000>;

> +		interrupts = <0 163 0x4>;

> +		clocks = <&clk_alw_0_8>;

> +		phy-mode = "rgmii";

> +		max-speed = <1000>;

> +		max-frame-size = <9000>;

> +		local-mac-address = [ a4 17 31 00 00 ed ];

> +		phy-handle = <&ethphy0>;

> +

> +		#address-cells = <1>;

> +		#size-cells = <0>;

> +

> +		ethphy0: ethernet-phy@1 {

> +			device_type = "ethernet-phy";

> +			compatible = "ethernet-phy-ieee802.3-c22";

> +			reg = <1>;

> +		};

> +	};

> -- 

> 2.7.4

> 

> --

> To unsubscribe from this list: send the line "unsubscribe devicetree" in

> the body of a message to majordomo@vger.kernel.org

> More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt
new file mode 100644
index 0000000..12d596c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt
@@ -0,0 +1,46 @@ 
+* Socionext NetSec Ethernet Controller IP
+
+Required properties:
+- compatible: Should be "socionext,netsecv5"
+- reg: Address and length of the register sets, the first is the main
+	registers, then the rdlar and tdlar regions for the SoC
+- interrupts: Should contain ethernet controller interrupt
+- clocks: phandle to any clocks to be switched by runtime_pm
+- phy-mode: See ethernet.txt file in the same directory
+- max-speed: See ethernet.txt file in the same directory
+- max-frame-size: See ethernet.txt file in the same directory, if 9000 or
+	above jumbo frames are enabled
+- local-mac-address: See ethernet.txt file in the same directory
+- phy-handle: phandle to select child phy
+
+Optional properties:
+- use-jumbo: Boolean property to suggest if jumbo packets should be used or not
+
+For the child phy
+
+- compatible "ethernet-phy-ieee802.3-c22" is needed
+- device_type "ethernet-phy"
+- reg: phy address
+
+
+Example:
+	eth0: ethernet {
+		compatible = "socionext,netsecv5";
+		reg = <0 0x31600000 0x10000>, <0 0x31618000 0x4000>, <0 0x3161c000 0x4000>;
+		interrupts = <0 163 0x4>;
+		clocks = <&clk_alw_0_8>;
+		phy-mode = "rgmii";
+		max-speed = <1000>;
+		max-frame-size = <9000>;
+		local-mac-address = [ a4 17 31 00 00 ed ];
+		phy-handle = <&ethphy0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			device_type = "ethernet-phy";
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+		};
+	};