diff mbox series

[v2,08/15] media: dt-bindings: add bindings for i.MX7 media driver

Message ID 20180423134750.30403-9-rui.silva@linaro.org
State New
Headers show
Series media: staging/imx7: add i.MX7 media driver | expand

Commit Message

Rui Miguel Silva April 23, 2018, 1:47 p.m. UTC
Add bindings documentation for i.MX7 media drivers.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>

---
 .../devicetree/bindings/media/imx7.txt        | 158 ++++++++++++++++++
 1 file changed, 158 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/imx7.txt

-- 
2.17.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Comments

Rob Herring (Arm) April 27, 2018, 7:06 p.m. UTC | #1
On Mon, Apr 23, 2018 at 02:47:43PM +0100, Rui Miguel Silva wrote:
> Add bindings documentation for i.MX7 media drivers.

> 

> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>

> ---

>  .../devicetree/bindings/media/imx7.txt        | 158 ++++++++++++++++++

>  1 file changed, 158 insertions(+)

>  create mode 100644 Documentation/devicetree/bindings/media/imx7.txt

> 

> diff --git a/Documentation/devicetree/bindings/media/imx7.txt b/Documentation/devicetree/bindings/media/imx7.txt

> new file mode 100644

> index 000000000000..7e058ea25102

> --- /dev/null

> +++ b/Documentation/devicetree/bindings/media/imx7.txt

> @@ -0,0 +1,158 @@

> +Freescale i.MX7 Media Video Device

> +==================================

> +

> +Video Media Controller node

> +---------------------------

> +

> +This is the media controller node for video capture support. It is a

> +virtual device that lists the camera serial interface nodes that the

> +media device will control.

> +

> +Required properties:

> +- compatible : "fsl,imx7-capture-subsystem";

> +- ports      : Should contain a list of phandles pointing to camera

> +		sensor interface port of CSI

> +

> +example:

> +

> +capture-subsystem {

> +	compatible = "fsl,imx7-capture-subsystem";

> +	ports = <&csi>;


Why do you need this node? Just have the driver match on the CSI node.

> +};

> +

> +

> +mipi_csi2 node

> +--------------

> +

> +This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is

> +compatible with previous version of Samsung D-phy.


Compatible with Samsung?

> +

> +Required properties:

> +

> +- compatible    : "fsl,imx7-mipi-csi2";

> +- reg           : base address and length of the register set for the device;

> +- interrupts    : should contain MIPI CSIS interrupt;

> +- clocks        : list of clock specifiers, see

> +        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;

> +- clock-names   : must contain "mipi" and "phy" entries, matching entries in the

> +                  clock property;

> +- power-domains : a phandle to the power domain, see

> +          Documentation/devicetree/bindings/power/power_domain.txt for details.

> +- reset-names   : should include following entry "mrst";

> +- resets        : a list of phandle, should contain reset entry of

> +                  reset-names;

> +- phy-supply    : from the generic phy bindings, a phandle to a regulator that

> +	          provides power to VBUS;


VBUS? Copy-n-paste from USB something?

> +- bus-width     : maximum number of data lanes supported (SoC specific);


Don't we have a standard lanes property for CSI (or DSI)? bus-width is 
for parallel buses and goes in endpoint nodes. (But maybe it got used 
here too).

> +

> +Optional properties:

> +

> +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default

> +		    value when this property is not specified is 166 MHz;

> +

> +port node

> +---------

> +

> +- reg		  : (required) can take the values 0 or 1, where 0 is the

> +                     related sink port and port 1 should be the source one;

> +

> +endpoint node

> +-------------

> +

> +- data-lanes    : (required) an array specifying active physical MIPI-CSI2

> +		    data input lanes and their mapping to logical lanes; the

> +		    array's content is unused, only its length is meaningful;


Ah yes, like this. :) So why do you need bus-width too?

> +

> +- csis-hs-settle : (optional) differential receiver (HS-RX) settle time;


units?

> +- csis-clk-settle : (optional) D-PHY control register;

> +- csis-wclk     : CSI-2 wrapper clock selection. If this property is present

> +		  external clock from CMU will be used, or the bus clock if

> +		  if it's not specified.


boolean?

These 3 need vendor properties.

> +

> +example:

> +

> +	mipi_csi: mipi-csi@30750000 {

> +                clock-frequency = <166000000>;

> +                status = "okay";

> +                #address-cells = <1>;

> +                #size-cells = <0>;

> +

> +		compatible = "fsl,imx7-mipi-csi2";

> +		reg = <0x30750000 0x10000>;

> +		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;

> +		clocks = <&clks IMX7D_MIPI_CSI_ROOT_CLK>,

> +				<&clks IMX7D_MIPI_DPHY_ROOT_CLK>;

> +		clock-names = "mipi", "phy";

> +		power-domains = <&pgc_mipi_phy>;

> +		phy-supply = <&reg_1p0d>;

> +		resets = <&src IMX7_RESET_MIPI_PHY_MRST>;

> +		reset-names = "mrst";

> +		bus-width = <4>;

> +		status = "disabled";

> +

> +                port@0 {

> +                        reg = <0>;

> +

> +                        mipi_from_sensor: endpoint {

> +                                remote-endpoint = <&ov2680_to_mipi>;

> +                                data-lanes = <1>;

> +                                csis-hs-settle = <3>;

> +                                csis-clk-settle = <0>;

> +                                csis-wclk;

> +                        };

> +                };

> +

> +                port@1 {

> +                        reg = <1>;

> +

> +                        mipi_vc0_to_csi_mux: endpoint {

> +                                remote-endpoint = <&csi_mux_from_mipi_vc0>;

> +                        };

> +                };

> +	};

> +

> +

> +csi node

> +--------

> +

> +This is device node for the CMOS Sensor Interface (CSI) which enables the chip

> +to connect directly to external CMOS image sensors.

> +

> +Required properties:

> +

> +- compatible    : "fsl,imx7-csi";

> +- reg           : base address and length of the register set for the device;

> +- interrupts    : should contain CSI interrupt;

> +- clocks        : list of clock specifiers, see

> +        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;

> +- clock-names   : must contain "axi", "mclk" and "dcic" entries, matching

> +                 entries in the clock property;

> +

> +port node

> +---------

> +

> +- reg		  : (required) should be 0 for the sink port;

> +

> +example:

> +

> +		csi: csi@30710000 {

> +                        #address-cells = <1>;

> +                        #size-cells = <0>;


Something wrong with indentation here.

> +

> +			compatible = "fsl,imx7-csi";

> +			reg = <0x30710000 0x10000>;

> +			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;

> +			clocks = <&clks IMX7D_CLK_DUMMY>,

> +					<&clks IMX7D_CSI_MCLK_ROOT_CLK>,

> +					<&clks IMX7D_CLK_DUMMY>;

> +			clock-names = "axi", "mclk", "dcic";

> +			status = "disabled";


Don't show status in examples.

> +

> +                        port@0 {


And the indentation here...


Same issues in the 1st example, too.

> +                                reg = <0>;

> +

> +                                csi_from_csi_mux: endpoint {

> +                                        remote-endpoint = <&csi_mux_to_csi>;

> +                                };

> +                        };

> +		};

> -- 

> 2.17.0

> 

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/media/imx7.txt b/Documentation/devicetree/bindings/media/imx7.txt
new file mode 100644
index 000000000000..7e058ea25102
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx7.txt
@@ -0,0 +1,158 @@ 
+Freescale i.MX7 Media Video Device
+==================================
+
+Video Media Controller node
+---------------------------
+
+This is the media controller node for video capture support. It is a
+virtual device that lists the camera serial interface nodes that the
+media device will control.
+
+Required properties:
+- compatible : "fsl,imx7-capture-subsystem";
+- ports      : Should contain a list of phandles pointing to camera
+		sensor interface port of CSI
+
+example:
+
+capture-subsystem {
+	compatible = "fsl,imx7-capture-subsystem";
+	ports = <&csi>;
+};
+
+
+mipi_csi2 node
+--------------
+
+This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is
+compatible with previous version of Samsung D-phy.
+
+Required properties:
+
+- compatible    : "fsl,imx7-mipi-csi2";
+- reg           : base address and length of the register set for the device;
+- interrupts    : should contain MIPI CSIS interrupt;
+- clocks        : list of clock specifiers, see
+        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
+- clock-names   : must contain "mipi" and "phy" entries, matching entries in the
+                  clock property;
+- power-domains : a phandle to the power domain, see
+          Documentation/devicetree/bindings/power/power_domain.txt for details.
+- reset-names   : should include following entry "mrst";
+- resets        : a list of phandle, should contain reset entry of
+                  reset-names;
+- phy-supply    : from the generic phy bindings, a phandle to a regulator that
+	          provides power to VBUS;
+- bus-width     : maximum number of data lanes supported (SoC specific);
+
+Optional properties:
+
+- clock-frequency : The IP's main (system bus) clock frequency in Hz, default
+		    value when this property is not specified is 166 MHz;
+
+port node
+---------
+
+- reg		  : (required) can take the values 0 or 1, where 0 is the
+                     related sink port and port 1 should be the source one;
+
+endpoint node
+-------------
+
+- data-lanes    : (required) an array specifying active physical MIPI-CSI2
+		    data input lanes and their mapping to logical lanes; the
+		    array's content is unused, only its length is meaningful;
+
+- csis-hs-settle : (optional) differential receiver (HS-RX) settle time;
+- csis-clk-settle : (optional) D-PHY control register;
+- csis-wclk     : CSI-2 wrapper clock selection. If this property is present
+		  external clock from CMU will be used, or the bus clock if
+		  if it's not specified.
+
+example:
+
+	mipi_csi: mipi-csi@30750000 {
+                clock-frequency = <166000000>;
+                status = "okay";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+		compatible = "fsl,imx7-mipi-csi2";
+		reg = <0x30750000 0x10000>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
+				<&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
+		clock-names = "mipi", "phy";
+		power-domains = <&pgc_mipi_phy>;
+		phy-supply = <&reg_1p0d>;
+		resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
+		reset-names = "mrst";
+		bus-width = <4>;
+		status = "disabled";
+
+                port@0 {
+                        reg = <0>;
+
+                        mipi_from_sensor: endpoint {
+                                remote-endpoint = <&ov2680_to_mipi>;
+                                data-lanes = <1>;
+                                csis-hs-settle = <3>;
+                                csis-clk-settle = <0>;
+                                csis-wclk;
+                        };
+                };
+
+                port@1 {
+                        reg = <1>;
+
+                        mipi_vc0_to_csi_mux: endpoint {
+                                remote-endpoint = <&csi_mux_from_mipi_vc0>;
+                        };
+                };
+	};
+
+
+csi node
+--------
+
+This is device node for the CMOS Sensor Interface (CSI) which enables the chip
+to connect directly to external CMOS image sensors.
+
+Required properties:
+
+- compatible    : "fsl,imx7-csi";
+- reg           : base address and length of the register set for the device;
+- interrupts    : should contain CSI interrupt;
+- clocks        : list of clock specifiers, see
+        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
+- clock-names   : must contain "axi", "mclk" and "dcic" entries, matching
+                 entries in the clock property;
+
+port node
+---------
+
+- reg		  : (required) should be 0 for the sink port;
+
+example:
+
+		csi: csi@30710000 {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+			compatible = "fsl,imx7-csi";
+			reg = <0x30710000 0x10000>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks IMX7D_CLK_DUMMY>,
+					<&clks IMX7D_CSI_MCLK_ROOT_CLK>,
+					<&clks IMX7D_CLK_DUMMY>;
+			clock-names = "axi", "mclk", "dcic";
+			status = "disabled";
+
+                        port@0 {
+                                reg = <0>;
+
+                                csi_from_csi_mux: endpoint {
+                                        remote-endpoint = <&csi_mux_to_csi>;
+                                };
+                        };
+		};