diff mbox series

[v9,01/23] x86/decompressor: Don't rely on upper 32 bits of GPRs being preserved

Message ID 20230807162720.545787-2-ardb@kernel.org
State New
Headers show
Series efi/x86: Avoid bare metal decompressor during EFI boot | expand

Commit Message

Ard Biesheuvel Aug. 7, 2023, 4:26 p.m. UTC
The 4-to-5 level mode switch trampoline disables long mode and paging in
order to be able to flick the LA57 bit. According to section 3.4.1.1 of
the x86 architecture manual [0], 64-bit GPRs might not retain the upper
32 bits of their contents across such a mode switch.

Given that RBP, RBX and RSI are live at this point, preserve them on the
stack, along with the return address that might be above 4G as well.

[0] Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 1: Basic Architecture

  "Because the upper 32 bits of 64-bit general-purpose registers are
   undefined in 32-bit modes, the upper 32 bits of any general-purpose
   register are not preserved when switching from 64-bit mode to a 32-bit
   mode (to protected mode or compatibility mode). Software must not
   depend on these bits to maintain a value after a 64-bit to 32-bit
   mode switch."

Fixes: 194a9749c73d650c ("x86/boot/compressed/64: Handle 5-level paging boot if kernel is above 4G")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
---
 arch/x86/boot/compressed/head_64.S | 30 +++++++++++++++-----
 1 file changed, 23 insertions(+), 7 deletions(-)
diff mbox series

Patch

diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S
index 03c4328a88cbd5d0..f732426d3b483139 100644
--- a/arch/x86/boot/compressed/head_64.S
+++ b/arch/x86/boot/compressed/head_64.S
@@ -459,11 +459,25 @@  SYM_CODE_START(startup_64)
 	/* Save the trampoline address in RCX */
 	movq	%rax, %rcx
 
+	/* Set up 32-bit addressable stack */
+	leaq	TRAMPOLINE_32BIT_STACK_END(%rcx), %rsp
+
 	/*
-	 * Load the address of trampoline_return() into RDI.
-	 * It will be used by the trampoline to return to the main code.
+	 * Preserve live 64-bit registers on the stack: this is necessary
+	 * because the architecture does not guarantee that GPRs will retain
+	 * their full 64-bit values across a 32-bit mode switch.
+	 */
+	pushq	%rbp
+	pushq	%rbx
+	pushq	%rsi
+
+	/*
+	 * Push the 64-bit address of trampoline_return() onto the new stack.
+	 * It will be used by the trampoline to return to the main code. Due to
+	 * the 32-bit mode switch, it cannot be kept it in a register either.
 	 */
 	leaq	trampoline_return(%rip), %rdi
+	pushq	%rdi
 
 	/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
 	pushq	$__KERNEL32_CS
@@ -471,6 +485,11 @@  SYM_CODE_START(startup_64)
 	pushq	%rax
 	lretq
 trampoline_return:
+	/* Restore live 64-bit registers */
+	popq	%rsi
+	popq	%rbx
+	popq	%rbp
+
 	/* Restore the stack, the 32-bit trampoline uses its own stack */
 	leaq	rva(boot_stack_end)(%rbx), %rsp
 
@@ -582,7 +601,7 @@  SYM_FUNC_END(.Lrelocated)
 /*
  * This is the 32-bit trampoline that will be copied over to low memory.
  *
- * RDI contains the return address (might be above 4G).
+ * Return address is at the top of the stack (might be above 4G).
  * ECX contains the base address of the trampoline memory.
  * Non zero RDX means trampoline needs to enable 5-level paging.
  */
@@ -592,9 +611,6 @@  SYM_CODE_START(trampoline_32bit_src)
 	movl	%eax, %ds
 	movl	%eax, %ss
 
-	/* Set up new stack */
-	leal	TRAMPOLINE_32BIT_STACK_END(%ecx), %esp
-
 	/* Disable paging */
 	movl	%cr0, %eax
 	btrl	$X86_CR0_PG_BIT, %eax
@@ -671,7 +687,7 @@  SYM_CODE_END(trampoline_32bit_src)
 	.code64
 SYM_FUNC_START_LOCAL_NOALIGN(.Lpaging_enabled)
 	/* Return from the trampoline */
-	jmp	*%rdi
+	retq
 SYM_FUNC_END(.Lpaging_enabled)
 
 	/*