diff mbox series

[v6,10/11] ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards

Message ID 20231010125719.784627-11-gatien.chevallier@foss.st.com
State New
Headers show
Series Introduce STM32 Firewall framework | expand

Commit Message

Gatien CHEVALLIER Oct. 10, 2023, 12:57 p.m. UTC
ETZPC is a firewall controller. Put all peripherals filtered by the
ETZPC as ETZPC subnodes and reference ETZPC as an
access-control-provider.

For more information on which peripheral is securable or supports MCU
isolation, please read the STM32MP15 reference manual.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V6:
    	- Renamed access-controller to access-controllers
    	- Removal of access-control-provider property

Changes in V5:
    	- Renamed feature-domain* to access-control*

 arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 +++++++++++++------------
 arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
 arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
 3 files changed, 1450 insertions(+), 1377 deletions(-)

Comments

Gatien CHEVALLIER Oct. 11, 2023, 8:49 a.m. UTC | #1
Hi Rob,

On 10/10/23 20:42, Rob Herring wrote:
> On Tue, Oct 10, 2023 at 02:57:18PM +0200, Gatien Chevallier wrote:
>> ETZPC is a firewall controller. Put all peripherals filtered by the
>> ETZPC as ETZPC subnodes and reference ETZPC as an
>> access-control-provider.
>>
>> For more information on which peripheral is securable or supports MCU
>> isolation, please read the STM32MP15 reference manual.
>>
>> Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
>> ---
>>
>> Changes in V6:
>>      	- Renamed access-controller to access-controllers
>>      	- Removal of access-control-provider property
>>
>> Changes in V5:
>>      	- Renamed feature-domain* to access-control*
>>
>>   arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 +++++++++++++------------
>>   arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
>>   arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
>>   3 files changed, 1450 insertions(+), 1377 deletions(-)
> 
> This is not reviewable. Change the indentation and any non-functional
> change in one patch and then actual changes in another.

Ok, I'll make it easier to read.

> 
> This is also an ABI break. Though I'm not sure it's avoidable. All the
> devices below the ETZPC node won't probe on existing kernel. A
> simple-bus fallback for ETZPC node should solve that.
> 

I had one issue when trying with a simple-bus fallback that was the
drivers were probing even though the access rights aren't correct.
Hence the removal of the simple-bus compatible in the STM32MP25 patch.

Even though a node is tagged with the OF_POPULATED flag when checking
the access rights with the firewall controller, it seems that when
simple-bus is probing, there's no check of this flag.

of_platform_populate() checks and sets the OF_POPULATED_BUS flag.
Maybe that is my error and the firewall bus populate should set
OF_POPULATED_BUS instead of OF_POPULATED. Is that correct?

Best regards,
Gatien

> Rob
Rob Herring (Arm) Oct. 12, 2023, 3:30 p.m. UTC | #2
On Wed, Oct 11, 2023 at 10:49:58AM +0200, Gatien CHEVALLIER wrote:
> Hi Rob,
> 
> On 10/10/23 20:42, Rob Herring wrote:
> > On Tue, Oct 10, 2023 at 02:57:18PM +0200, Gatien Chevallier wrote:
> > > ETZPC is a firewall controller. Put all peripherals filtered by the
> > > ETZPC as ETZPC subnodes and reference ETZPC as an
> > > access-control-provider.
> > > 
> > > For more information on which peripheral is securable or supports MCU
> > > isolation, please read the STM32MP15 reference manual.
> > > 
> > > Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
> > > ---
> > > 
> > > Changes in V6:
> > >      	- Renamed access-controller to access-controllers
> > >      	- Removal of access-control-provider property
> > > 
> > > Changes in V5:
> > >      	- Renamed feature-domain* to access-control*
> > > 
> > >   arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 +++++++++++++------------
> > >   arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
> > >   arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
> > >   3 files changed, 1450 insertions(+), 1377 deletions(-)
> > 
> > This is not reviewable. Change the indentation and any non-functional
> > change in one patch and then actual changes in another.
> 
> Ok, I'll make it easier to read.
> 
> > 
> > This is also an ABI break. Though I'm not sure it's avoidable. All the
> > devices below the ETZPC node won't probe on existing kernel. A
> > simple-bus fallback for ETZPC node should solve that.
> > 
> 
> I had one issue when trying with a simple-bus fallback that was the
> drivers were probing even though the access rights aren't correct.
> Hence the removal of the simple-bus compatible in the STM32MP25 patch.

But it worked before, right? So the difference is you have either added 
new devices which need setup or your firmware changed how devices are 
setup (or not setup). Certainly can't fix the latter case. You just need 
to be explicit about what you are doing to users.


> Even though a node is tagged with the OF_POPULATED flag when checking
> the access rights with the firewall controller, it seems that when
> simple-bus is probing, there's no check of this flag.

It shouldn't. Those flags are for creating the devices (or not) and 
removing only devices of_platform_populate() created.

> of_platform_populate() checks and sets the OF_POPULATED_BUS flag.
> Maybe that is my error and the firewall bus populate should set
> OF_POPULATED_BUS instead of OF_POPULATED. Is that correct?

Shrug. Off hand, I'd say probably not, but am not certain.

Rob
Gatien CHEVALLIER Oct. 16, 2023, 12:02 p.m. UTC | #3
Hi Rob,

On 10/12/23 17:30, Rob Herring wrote:
> On Wed, Oct 11, 2023 at 10:49:58AM +0200, Gatien CHEVALLIER wrote:
>> Hi Rob,
>>
>> On 10/10/23 20:42, Rob Herring wrote:
>>> On Tue, Oct 10, 2023 at 02:57:18PM +0200, Gatien Chevallier wrote:
>>>> ETZPC is a firewall controller. Put all peripherals filtered by the
>>>> ETZPC as ETZPC subnodes and reference ETZPC as an
>>>> access-control-provider.
>>>>
>>>> For more information on which peripheral is securable or supports MCU
>>>> isolation, please read the STM32MP15 reference manual.
>>>>
>>>> Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
>>>> ---
>>>>
>>>> Changes in V6:
>>>>       	- Renamed access-controller to access-controllers
>>>>       	- Removal of access-control-provider property
>>>>
>>>> Changes in V5:
>>>>       	- Renamed feature-domain* to access-control*
>>>>
>>>>    arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 +++++++++++++------------
>>>>    arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
>>>>    arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
>>>>    3 files changed, 1450 insertions(+), 1377 deletions(-)
>>>
>>> This is not reviewable. Change the indentation and any non-functional
>>> change in one patch and then actual changes in another.
>>
>> Ok, I'll make it easier to read.
>>
>>>
>>> This is also an ABI break. Though I'm not sure it's avoidable. All the
>>> devices below the ETZPC node won't probe on existing kernel. A
>>> simple-bus fallback for ETZPC node should solve that.
>>>
>>
>> I had one issue when trying with a simple-bus fallback that was the
>> drivers were probing even though the access rights aren't correct.
>> Hence the removal of the simple-bus compatible in the STM32MP25 patch.
> 
> But it worked before, right? So the difference is you have either added
> new devices which need setup or your firmware changed how devices are
> setup (or not setup). Certainly can't fix the latter case. You just need
> to be explicit about what you are doing to users.
> 

I should've specified it was during a test where I deliberately set
incorrect rights on a peripheral and enabled its node to see if the
firewall would allow the creation of the device.

> 
>> Even though a node is tagged with the OF_POPULATED flag when checking
>> the access rights with the firewall controller, it seems that when
>> simple-bus is probing, there's no check of this flag.
> 
> It shouldn't. Those flags are for creating the devices (or not) and
> removing only devices of_platform_populate() created.
> 

About the "simple-bus" being a fallback, I think I understood why I saw
that the devices were created.

All devices under a node whose compatible is "simple-bus" are created
in of_platform_device_create_pdata(), called by
of_platform_default_populate_init() at arch_initcall level. This
before the firewall-controller has a chance to populate it's bus.

Therefore, when I flag nodes when populating the firewall-bus, the
devices are already created. The "simple-bus" mechanism is not a
fallback here as it precedes the driver probe.

Is there a safe way to safely remove/disable a device created this way?
Devices that are under the firewall controller (simple-bus) node
should not be probed before it as they're child of it.

Best regards,
Gatien

>> of_platform_populate() checks and sets the OF_POPULATED_BUS flag.
>> Maybe that is my error and the firewall bus populate should set
>> OF_POPULATED_BUS instead of OF_POPULATED. Is that correct?
> 
> Shrug. Off hand, I'd say probably not, but am not certain.
> 
> Rob
Rob Herring (Arm) Oct. 24, 2023, 4:39 p.m. UTC | #4
On Mon, Oct 16, 2023 at 02:02:39PM +0200, Gatien CHEVALLIER wrote:
> Hi Rob,
> 
> On 10/12/23 17:30, Rob Herring wrote:
> > On Wed, Oct 11, 2023 at 10:49:58AM +0200, Gatien CHEVALLIER wrote:
> > > Hi Rob,
> > > 
> > > On 10/10/23 20:42, Rob Herring wrote:
> > > > On Tue, Oct 10, 2023 at 02:57:18PM +0200, Gatien Chevallier wrote:
> > > > > ETZPC is a firewall controller. Put all peripherals filtered by the
> > > > > ETZPC as ETZPC subnodes and reference ETZPC as an
> > > > > access-control-provider.
> > > > > 
> > > > > For more information on which peripheral is securable or supports MCU
> > > > > isolation, please read the STM32MP15 reference manual.
> > > > > 
> > > > > Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
> > > > > ---
> > > > > 
> > > > > Changes in V6:
> > > > >       	- Renamed access-controller to access-controllers
> > > > >       	- Removal of access-control-provider property
> > > > > 
> > > > > Changes in V5:
> > > > >       	- Renamed feature-domain* to access-control*
> > > > > 
> > > > >    arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 +++++++++++++------------
> > > > >    arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
> > > > >    arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
> > > > >    3 files changed, 1450 insertions(+), 1377 deletions(-)
> > > > 
> > > > This is not reviewable. Change the indentation and any non-functional
> > > > change in one patch and then actual changes in another.
> > > 
> > > Ok, I'll make it easier to read.
> > > 
> > > > 
> > > > This is also an ABI break. Though I'm not sure it's avoidable. All the
> > > > devices below the ETZPC node won't probe on existing kernel. A
> > > > simple-bus fallback for ETZPC node should solve that.
> > > > 
> > > 
> > > I had one issue when trying with a simple-bus fallback that was the
> > > drivers were probing even though the access rights aren't correct.
> > > Hence the removal of the simple-bus compatible in the STM32MP25 patch.
> > 
> > But it worked before, right? So the difference is you have either added
> > new devices which need setup or your firmware changed how devices are
> > setup (or not setup). Certainly can't fix the latter case. You just need
> > to be explicit about what you are doing to users.
> > 
> 
> I should've specified it was during a test where I deliberately set
> incorrect rights on a peripheral and enabled its node to see if the
> firewall would allow the creation of the device.
> 
> > 
> > > Even though a node is tagged with the OF_POPULATED flag when checking
> > > the access rights with the firewall controller, it seems that when
> > > simple-bus is probing, there's no check of this flag.
> > 
> > It shouldn't. Those flags are for creating the devices (or not) and
> > removing only devices of_platform_populate() created.
> > 
> 
> About the "simple-bus" being a fallback, I think I understood why I saw
> that the devices were created.
> 
> All devices under a node whose compatible is "simple-bus" are created
> in of_platform_device_create_pdata(), called by
> of_platform_default_populate_init() at arch_initcall level. This
> before the firewall-controller has a chance to populate it's bus.
> 
> Therefore, when I flag nodes when populating the firewall-bus, the
> devices are already created. The "simple-bus" mechanism is not a
> fallback here as it precedes the driver probe.
> 
> Is there a safe way to safely remove/disable a device created this way?

There's 2 ways to handle this. Either controlling creating the device or 
controlling probing the device. The latter should just work with 
fw_devlink dependency. The former probably needs some adjustment to 
simple-pm-bus driver if you have 'simple-bus' compatible. You want it to 
probe on old kernels and not probe on new kernels with your firewall 
driver. Look at the commit history for simple-pm-bus. There was some 
discussion on it as well.

> Devices that are under the firewall controller (simple-bus) node
> should not be probed before it as they're child of it.

fw_devlink should take care of parent/child dependencies without any 
explicit handling of the access ctrl binding.

Rob
Gatien CHEVALLIER Nov. 27, 2023, 1:46 p.m. UTC | #5
Hi,

A gentle reminder on the questions below.

I'm also thinking about moving the STM32 firewall framework to a
specific access-controllers folder if that's ok.

Best regards,
Gatien

On 10/27/23 17:37, Gatien CHEVALLIER wrote:
> 
> 
> On 10/24/23 18:39, Rob Herring wrote:
>> On Mon, Oct 16, 2023 at 02:02:39PM +0200, Gatien CHEVALLIER wrote:
>>> Hi Rob,
>>>
>>> On 10/12/23 17:30, Rob Herring wrote:
>>>> On Wed, Oct 11, 2023 at 10:49:58AM +0200, Gatien CHEVALLIER wrote:
>>>>> Hi Rob,
>>>>>
>>>>> On 10/10/23 20:42, Rob Herring wrote:
>>>>>> On Tue, Oct 10, 2023 at 02:57:18PM +0200, Gatien Chevallier wrote:
>>>>>>> ETZPC is a firewall controller. Put all peripherals filtered by the
>>>>>>> ETZPC as ETZPC subnodes and reference ETZPC as an
>>>>>>> access-control-provider.
>>>>>>>
>>>>>>> For more information on which peripheral is securable or supports 
>>>>>>> MCU
>>>>>>> isolation, please read the STM32MP15 reference manual.
>>>>>>>
>>>>>>> Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
>>>>>>> ---
>>>>>>>
>>>>>>> Changes in V6:
>>>>>>>            - Renamed access-controller to access-controllers
>>>>>>>            - Removal of access-control-provider property
>>>>>>>
>>>>>>> Changes in V5:
>>>>>>>            - Renamed feature-domain* to access-control*
>>>>>>>
>>>>>>>     arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 
>>>>>>> +++++++++++++------------
>>>>>>>     arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
>>>>>>>     arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
>>>>>>>     3 files changed, 1450 insertions(+), 1377 deletions(-)
>>>>>>
>>>>>> This is not reviewable. Change the indentation and any non-functional
>>>>>> change in one patch and then actual changes in another.
>>>>>
>>>>> Ok, I'll make it easier to read.
>>>>>
>>>>>>
>>>>>> This is also an ABI break. Though I'm not sure it's avoidable. All 
>>>>>> the
>>>>>> devices below the ETZPC node won't probe on existing kernel. A
>>>>>> simple-bus fallback for ETZPC node should solve that.
>>>>>>
>>>>>
>>>>> I had one issue when trying with a simple-bus fallback that was the
>>>>> drivers were probing even though the access rights aren't correct.
>>>>> Hence the removal of the simple-bus compatible in the STM32MP25 patch.
>>>>
>>>> But it worked before, right? So the difference is you have either added
>>>> new devices which need setup or your firmware changed how devices are
>>>> setup (or not setup). Certainly can't fix the latter case. You just 
>>>> need
>>>> to be explicit about what you are doing to users.
>>>>
>>>
>>> I should've specified it was during a test where I deliberately set
>>> incorrect rights on a peripheral and enabled its node to see if the
>>> firewall would allow the creation of the device.
>>>
>>>>
>>>>> Even though a node is tagged with the OF_POPULATED flag when checking
>>>>> the access rights with the firewall controller, it seems that when
>>>>> simple-bus is probing, there's no check of this flag.
>>>>
>>>> It shouldn't. Those flags are for creating the devices (or not) and
>>>> removing only devices of_platform_populate() created.
>>>>
>>>
>>> About the "simple-bus" being a fallback, I think I understood why I saw
>>> that the devices were created.
>>>
>>> All devices under a node whose compatible is "simple-bus" are created
>>> in of_platform_device_create_pdata(), called by
>>> of_platform_default_populate_init() at arch_initcall level. This
>>> before the firewall-controller has a chance to populate it's bus.
>>>
>>> Therefore, when I flag nodes when populating the firewall-bus, the
>>> devices are already created. The "simple-bus" mechanism is not a
>>> fallback here as it precedes the driver probe.
>>>
>>> Is there a safe way to safely remove/disable a device created this way?
>>
>> There's 2 ways to handle this. Either controlling creating the device or
>> controlling probing the device. The latter should just work with
>> fw_devlink dependency. The former probably needs some adjustment to
>> simple-pm-bus driver if you have 'simple-bus' compatible. You want it to
>> probe on old kernels and not probe on new kernels with your firewall
>> driver. Look at the commit history for simple-pm-bus. There was some
>> discussion on it as well.
>>
> 
> Hi Rob,
> 
> First, thank you for your suggestions.
> 
> Regarding controlling probing the device: the philosophy of the firewall
> controller was to check a device secure configuration to determine if
> its associated driver should be probed (+handle some firewall
> resources). I'd rather avoid it so that the device isn't created at all.
> 
> I took a look on the simple-bus driver side. I don't see an obvious way
> on how to do it as the firewall controller driver is a module while the
> devices being populated is done at arch initcall level.
> 
> I ended up with two propositions:
> 
> 1)I took a shot at implementing a new flag "OF_ACCESS_GRANTED" that
> should be set in the first call of the of_platform_bus_create()
> function for every child node of a "default bus" (simple-bus,
> simple-pm-bus, ...) having the access-controllers property.
> This flag should be unset by the access controller if the access is
> not granted. This covers the particular case where the access controller
> has a simple-bus fallback whilst not creating the devices on the first
> try for the bus' childs.
> 
> This way, the first round of of_platform_populate() done at arch init
> call level won't create the devices of an access controller child
> nodes. Then, the firewall controller has a chance to clear the flag
> before the second call to this function by the simple-pm-bus driver.
> 
> If the controller module isn't present, then it's a simple-bus
> behavior to extent of the child devices not being all created in the
> first place. This shouldn't be an issue as in only concerns childs
> of such bus that aren't probed before the bus driver.
> 
> I have a patch that I can send as RFC on top of my series if my
> explanation isn't clear enough.
> 
> 2)Make the STM32_FIREWALL configuration switch select the OF_DYNAMIC
> one. This way I can use of_detach_node() function to remove the node
> from the device tree. The cons of this is the device tree is now
> used at runtime.
> 
> Are you considering one of these two proposition as a viable solution?
> 
> Best regards,
> Gatien
> 
>>> Devices that are under the firewall controller (simple-bus) node
>>> should not be probed before it as they're child of it.
>>
>> fw_devlink should take care of parent/child dependencies without any
>> explicit handling of the access ctrl binding.
>>
>> Rob
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/st/stm32mp151.dtsi b/arch/arm/boot/dts/st/stm32mp151.dtsi
index 61508917521c..e66970cd8745 100644
--- a/arch/arm/boot/dts/st/stm32mp151.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp151.dtsi
@@ -122,1543 +122,1615 @@  soc {
 		interrupt-parent = <&intc>;
 		ranges;
 
-		timers2: timer@40000000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40000000 0x400>;
-			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM2_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 18 0x400 0x1>,
-			       <&dmamux1 19 0x400 0x1>,
-			       <&dmamux1 20 0x400 0x1>,
-			       <&dmamux1 21 0x400 0x1>,
-			       <&dmamux1 22 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+		ipcc: mailbox@4c001000 {
+			compatible = "st,stm32mp1-ipcc";
+			#mbox-cells = <1>;
+			reg = <0x4c001000 0x400>;
+			st,proc-id = <0>;
+			interrupts-extended =
+				<&exti 61 1>,
+				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
+			clocks = <&rcc IPCC>;
+			wakeup-source;
 			status = "disabled";
+		};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@1 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <1>;
-				status = "disabled";
-			};
-
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
-			};
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp1-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
-		timers3: timer@40001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40001000 0x400>;
-			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM3_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 23 0x400 0x1>,
-			       <&dmamux1 24 0x400 0x1>,
-			       <&dmamux1 25 0x400 0x1>,
-			       <&dmamux1 26 0x400 0x1>,
-			       <&dmamux1 27 0x400 0x1>,
-			       <&dmamux1 28 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
-			status = "disabled";
+		pwr_regulators: pwr@50001000 {
+			compatible = "st,stm32mp1,pwr-reg";
+			reg = <0x50001000 0x10>;
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
+			reg11: reg11 {
+				regulator-name = "reg11";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
 			};
 
-			timer@2 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <2>;
-				status = "disabled";
+			reg18: reg18 {
+				regulator-name = "reg18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 			};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
+			usb33: usb33 {
+				regulator-name = "usb33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 			};
 		};
 
-		timers4: timer@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40002000 0x400>;
-			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM4_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 29 0x400 0x1>,
-			       <&dmamux1 30 0x400 0x1>,
-			       <&dmamux1 31 0x400 0x1>,
-			       <&dmamux1 32 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
+		pwr_mcu: pwr_mcu@50001014 {
+			compatible = "st,stm32mp151-pwr-mcu", "syscon";
+			reg = <0x50001014 0x4>;
+		};
 
-			timer@3 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <3>;
-				status = "disabled";
-			};
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp1-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
-			};
+		syscfg: syscon@50020000 {
+			compatible = "st,stm32mp157-syscfg", "syscon";
+			reg = <0x50020000 0x400>;
+			clocks = <&rcc SYSCFG>;
 		};
 
-		timers5: timer@40003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40003000 0x400>;
-			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM5_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 55 0x400 0x1>,
-			       <&dmamux1 56 0x400 0x1>,
-			       <&dmamux1 57 0x400 0x1>,
-			       <&dmamux1 58 0x400 0x1>,
-			       <&dmamux1 59 0x400 0x1>,
-			       <&dmamux1 60 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+		dts: thermal@50028000 {
+			compatible = "st,stm32-thermal";
+			reg = <0x50028000 0x100>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc TMPSENS>;
+			clock-names = "pclk";
+			#thermal-sensor-cells = <0>;
 			status = "disabled";
+		};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@4 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <4>;
-				status = "disabled";
-			};
-
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
-			};
+		mdma1: dma-controller@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			resets = <&rcc MDMA_R>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
 		};
 
-		timers6: timer@40004000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40004000 0x400>;
-			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM6_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 69 0x400 0x1>;
-			dma-names = "up";
+		sdmmc1: mmc@58005000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58005000 0x1000>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC1_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC1_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
 			status = "disabled";
-
-			timer@5 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <5>;
-				status = "disabled";
-			};
 		};
 
-		timers7: timer@40005000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40005000 0x400>;
-			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM7_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 70 0x400 0x1>;
-			dma-names = "up";
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58007000 0x1000>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
 			status = "disabled";
-
-			timer@6 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <6>;
-				status = "disabled";
-			};
 		};
 
-		timers12: timer@40006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40006000 0x400>;
-			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM12_K>;
-			clock-names = "int";
+		crc1: crc@58009000 {
+			compatible = "st,stm32f7-crc";
+			reg = <0x58009000 0x400>;
+			clocks = <&rcc CRC1>;
 			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@11 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <11>;
-				status = "disabled";
-			};
 		};
 
-		timers13: timer@40007000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40007000 0x400>;
-			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM13_K>;
-			clock-names = "int";
+		usbh_ohci: usb@5800c000 {
+			compatible = "generic-ohci";
+			reg = <0x5800c000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@12 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <12>;
-				status = "disabled";
-			};
 		};
 
-		timers14: timer@40008000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40008000 0x400>;
-			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM14_K>;
-			clock-names = "int";
+		usbh_ehci: usb@5800d000 {
+			compatible = "generic-ehci";
+			reg = <0x5800d000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			companion = <&usbh_ohci>;
 			status = "disabled";
+		};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
+		ltdc: display-controller@5a001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x5a001000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LTDC_PX>;
+			clock-names = "lcd";
+			resets = <&rcc LTDC_R>;
+			status = "disabled";
+		};
 
-			timer@13 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <13>;
-				status = "disabled";
-			};
+		iwdg2: watchdog@5a002000 {
+			compatible = "st,stm32mp1-iwdg";
+			reg = <0x5a002000 0x400>;
+			clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
+			clock-names = "pclk", "lsi";
+			status = "disabled";
 		};
 
-		lptimer1: timer@40009000 {
+		usbphyc: usbphyc@5a006000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x40009000 0x400>;
-			interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM1_K>;
-			clock-names = "mux";
-			wakeup-source;
+			#clock-cells = <0>;
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc USBPHY_K>;
+			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&reg11>;
+			vdda1v8-supply = <&reg18>;
 			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			trigger@0 {
-				compatible = "st,stm32-lptimer-trigger";
+			usbphyc_port0: usb-phy@0 {
+				#phy-cells = <0>;
 				reg = <0>;
-				status = "disabled";
 			};
 
-			counter {
-				compatible = "st,stm32-lptimer-counter";
-				status = "disabled";
+			usbphyc_port1: usb-phy@1 {
+				#phy-cells = <1>;
+				reg = <1>;
 			};
 		};
 
-		spi2: spi@4000b000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x4000b000 0x400>;
-			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI2_K>;
-			resets = <&rcc SPI2_R>;
-			dmas = <&dmamux1 39 0x400 0x05>,
-			       <&dmamux1 40 0x400 0x05>;
-			dma-names = "rx", "tx";
+		rtc: rtc@5c004000 {
+			compatible = "st,stm32mp1-rtc";
+			reg = <0x5c004000 0x400>;
+			clocks = <&rcc RTCAPB>, <&rcc RTC>;
+			clock-names = "pclk", "rtc_ck";
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
-		i2s2: audio-controller@4000b000 {
-			compatible = "st,stm32h7-i2s";
-			#sound-dai-cells = <0>;
-			reg = <0x4000b000 0x400>;
-			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 39 0x400 0x01>,
-			       <&dmamux1 40 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
+		bsec: efuse@5c005000 {
+			compatible = "st,stm32mp15-bsec";
+			reg = <0x5c005000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			part_number_otp: part-number-otp@4 {
+				reg = <0x4 0x1>;
+			};
+			vrefint: vrefin-cal@52 {
+				reg = <0x52 0x2>;
+			};
+			ts_cal1: calib@5c {
+				reg = <0x5c 0x2>;
+			};
+			ts_cal2: calib@5e {
+				reg = <0x5e 0x2>;
+			};
 		};
 
-		spi3: spi@4000c000 {
+		etzpc: bus@5c007000 {
+			compatible = "st,stm32-etzpc";
+			reg = <0x5c007000 0x400>;
 			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x4000c000 0x400>;
-			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI3_K>;
-			resets = <&rcc SPI3_R>;
-			dmas = <&dmamux1 61 0x400 0x05>,
-			       <&dmamux1 62 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			#size-cells = <1>;
+			#access-controller-cells = <1>;
+			ranges;
 
-		i2s3: audio-controller@4000c000 {
-			compatible = "st,stm32h7-i2s";
-			#sound-dai-cells = <0>;
-			reg = <0x4000c000 0x400>;
-			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 61 0x400 0x01>,
-			       <&dmamux1 62 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			timers2: timer@40000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40000000 0x400>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM2_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 18 0x400 0x1>,
+				       <&dmamux1 19 0x400 0x1>,
+				       <&dmamux1 20 0x400 0x1>,
+				       <&dmamux1 21 0x400 0x1>,
+				       <&dmamux1 22 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+				access-controllers = <&etzpc 16>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		spdifrx: audio-controller@4000d000 {
-			compatible = "st,stm32h7-spdifrx";
-			#sound-dai-cells = <0>;
-			reg = <0x4000d000 0x400>;
-			clocks = <&rcc SPDIF_K>;
-			clock-names = "kclk";
-			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 93 0x400 0x01>,
-			       <&dmamux1 94 0x400 0x01>;
-			dma-names = "rx", "rx-ctrl";
-			status = "disabled";
-		};
+				timer@1 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <1>;
+					status = "disabled";
+				};
 
-		usart2: serial@4000e000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x4000e000 0x400>;
-			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART2_K>;
-			wakeup-source;
-			dmas = <&dmamux1 43 0x400 0x15>,
-			       <&dmamux1 44 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-		usart3: serial@4000f000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x4000f000 0x400>;
-			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART3_K>;
-			wakeup-source;
-			dmas = <&dmamux1 45 0x400 0x15>,
-			       <&dmamux1 46 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			timers3: timer@40001000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40001000 0x400>;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM3_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 23 0x400 0x1>,
+				       <&dmamux1 24 0x400 0x1>,
+				       <&dmamux1 25 0x400 0x1>,
+				       <&dmamux1 26 0x400 0x1>,
+				       <&dmamux1 27 0x400 0x1>,
+				       <&dmamux1 28 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+				access-controllers = <&etzpc 17>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		uart4: serial@40010000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40010000 0x400>;
-			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART4_K>;
-			wakeup-source;
-			dmas = <&dmamux1 63 0x400 0x15>,
-			       <&dmamux1 64 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				timer@2 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <2>;
+					status = "disabled";
+				};
 
-		uart5: serial@40011000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40011000 0x400>;
-			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART5_K>;
-			wakeup-source;
-			dmas = <&dmamux1 65 0x400 0x15>,
-			       <&dmamux1 66 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-		i2c1: i2c@40012000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40012000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C1_K>;
-			resets = <&rcc I2C1_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x1>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+			timers4: timer@40002000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40002000 0x400>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM4_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 29 0x400 0x1>,
+				       <&dmamux1 30 0x400 0x1>,
+				       <&dmamux1 31 0x400 0x1>,
+				       <&dmamux1 32 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4";
+				access-controllers = <&etzpc 18>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		i2c2: i2c@40013000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40013000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C2_K>;
-			resets = <&rcc I2C2_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x2>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+				timer@3 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <3>;
+					status = "disabled";
+				};
 
-		i2c3: i2c@40014000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40014000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C3_K>;
-			resets = <&rcc I2C3_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x4>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-		i2c5: i2c@40015000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40015000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C5_K>;
-			resets = <&rcc I2C5_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x10>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+			timers5: timer@40003000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40003000 0x400>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM5_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 55 0x400 0x1>,
+				       <&dmamux1 56 0x400 0x1>,
+				       <&dmamux1 57 0x400 0x1>,
+				       <&dmamux1 58 0x400 0x1>,
+				       <&dmamux1 59 0x400 0x1>,
+				       <&dmamux1 60 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+				access-controllers = <&etzpc 19>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		cec: cec@40016000 {
-			compatible = "st,stm32-cec";
-			reg = <0x40016000 0x400>;
-			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CEC_K>, <&rcc CEC>;
-			clock-names = "cec", "hdmi-cec";
-			status = "disabled";
-		};
+				timer@4 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <4>;
+					status = "disabled";
+				};
 
-		dac: dac@40017000 {
-			compatible = "st,stm32h7-dac-core";
-			reg = <0x40017000 0x400>;
-			clocks = <&rcc DAC12>;
-			clock-names = "pclk";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-			dac1: dac@1 {
-				compatible = "st,stm32-dac";
-				#io-channel-cells = <1>;
-				reg = <1>;
-				status = "disabled";
+			timers6: timer@40004000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40004000 0x400>;
+				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM6_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 69 0x400 0x1>;
+				dma-names = "up";
+				access-controllers = <&etzpc 20>;
+				status = "disabled";
+
+				timer@5 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <5>;
+					status = "disabled";
+				};
 			};
 
-			dac2: dac@2 {
-				compatible = "st,stm32-dac";
-				#io-channel-cells = <1>;
-				reg = <2>;
-				status = "disabled";
+			timers7: timer@40005000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40005000 0x400>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM7_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 70 0x400 0x1>;
+				dma-names = "up";
+				access-controllers = <&etzpc 21>;
+				status = "disabled";
+
+				timer@6 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <6>;
+					status = "disabled";
+				};
 			};
-		};
 
-		uart7: serial@40018000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40018000 0x400>;
-			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART7_K>;
-			wakeup-source;
-			dmas = <&dmamux1 79 0x400 0x15>,
-			       <&dmamux1 80 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			timers12: timer@40006000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40006000 0x400>;
+				interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM12_K>;
+				clock-names = "int";
+				access-controllers = <&etzpc 22>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		uart8: serial@40019000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40019000 0x400>;
-			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART8_K>;
-			wakeup-source;
-			dmas = <&dmamux1 81 0x400 0x15>,
-			       <&dmamux1 82 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				timer@11 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <11>;
+					status = "disabled";
+				};
+			};
 
-		timers1: timer@44000000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44000000 0x400>;
-			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "brk", "up", "trg-com", "cc";
-			clocks = <&rcc TIM1_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 11 0x400 0x1>,
-			       <&dmamux1 12 0x400 0x1>,
-			       <&dmamux1 13 0x400 0x1>,
-			       <&dmamux1 14 0x400 0x1>,
-			       <&dmamux1 15 0x400 0x1>,
-			       <&dmamux1 16 0x400 0x1>,
-			       <&dmamux1 17 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4",
-				    "up", "trig", "com";
-			status = "disabled";
+			timers13: timer@40007000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40007000 0x400>;
+				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM13_K>;
+				clock-names = "int";
+				access-controllers = <&etzpc 23>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
+				timer@12 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <12>;
+					status = "disabled";
+				};
 			};
 
-			timer@0 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <0>;
-				status = "disabled";
-			};
+			timers14: timer@40008000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40008000 0x400>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM14_K>;
+				clock-names = "int";
+				access-controllers = <&etzpc 24>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
+				timer@13 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <13>;
+					status = "disabled";
+				};
 			};
-		};
 
-		timers8: timer@44001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44001000 0x400>;
-			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "brk", "up", "trg-com", "cc";
-			clocks = <&rcc TIM8_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 47 0x400 0x1>,
-			       <&dmamux1 48 0x400 0x1>,
-			       <&dmamux1 49 0x400 0x1>,
-			       <&dmamux1 50 0x400 0x1>,
-			       <&dmamux1 51 0x400 0x1>,
-			       <&dmamux1 52 0x400 0x1>,
-			       <&dmamux1 53 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4",
-				    "up", "trig", "com";
-			status = "disabled";
+			lptimer1: timer@40009000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x40009000 0x400>;
+				interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM1_K>;
+				clock-names = "mux";
+				wakeup-source;
+				access-controllers = <&etzpc 25>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
+				trigger@0 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <0>;
+					status = "disabled";
+				};
+
+				counter {
+					compatible = "st,stm32-lptimer-counter";
+					status = "disabled";
+				};
 			};
 
-			timer@7 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <7>;
+			i2s2: audio-controller@4000b000 {
+				compatible = "st,stm32h7-i2s";
+				#sound-dai-cells = <0>;
+				reg = <0x4000b000 0x400>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 39 0x400 0x01>,
+				       <&dmamux1 40 0x400 0x01>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 27>;
 				status = "disabled";
 			};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
+			spi2: spi@4000b000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x4000b000 0x400>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI2_K>;
+				resets = <&rcc SPI2_R>;
+				dmas = <&dmamux1 39 0x400 0x05>,
+				       <&dmamux1 40 0x400 0x05>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 27>;
 				status = "disabled";
 			};
-		};
-
-		usart6: serial@44003000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x44003000 0x400>;
-			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART6_K>;
-			wakeup-source;
-			dmas = <&dmamux1 71 0x400 0x15>,
-			       <&dmamux1 72 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		spi1: spi@44004000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x44004000 0x400>;
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI1_K>;
-			resets = <&rcc SPI1_R>;
-			dmas = <&dmamux1 37 0x400 0x05>,
-			       <&dmamux1 38 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		i2s1: audio-controller@44004000 {
-			compatible = "st,stm32h7-i2s";
-			#sound-dai-cells = <0>;
-			reg = <0x44004000 0x400>;
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 37 0x400 0x01>,
-			       <&dmamux1 38 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
 
-		spi4: spi@44005000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x44005000 0x400>;
-			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI4_K>;
-			resets = <&rcc SPI4_R>;
-			dmas = <&dmamux1 83 0x400 0x05>,
-			       <&dmamux1 84 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		timers15: timer@44006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44006000 0x400>;
-			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM15_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 105 0x400 0x1>,
-			       <&dmamux1 106 0x400 0x1>,
-			       <&dmamux1 107 0x400 0x1>,
-			       <&dmamux1 108 0x400 0x1>;
-			dma-names = "ch1", "up", "trig", "com";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
+			i2s3: audio-controller@4000c000 {
+				compatible = "st,stm32h7-i2s";
+				#sound-dai-cells = <0>;
+				reg = <0x4000c000 0x400>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 61 0x400 0x01>,
+				       <&dmamux1 62 0x400 0x01>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 28>;
 				status = "disabled";
 			};
 
-			timer@14 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <14>;
+			spi3: spi@4000c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x4000c000 0x400>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI3_K>;
+				resets = <&rcc SPI3_R>;
+				dmas = <&dmamux1 61 0x400 0x05>,
+				       <&dmamux1 62 0x400 0x05>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 28>;
 				status = "disabled";
 			};
-		};
-
-		timers16: timer@44007000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44007000 0x400>;
-			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM16_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 109 0x400 0x1>,
-			       <&dmamux1 110 0x400 0x1>;
-			dma-names = "ch1", "up";
-			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
+			spdifrx: audio-controller@4000d000 {
+				compatible = "st,stm32h7-spdifrx";
+				#sound-dai-cells = <0>;
+				reg = <0x4000d000 0x400>;
+				clocks = <&rcc SPDIF_K>;
+				clock-names = "kclk";
+				interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 93 0x400 0x01>,
+				       <&dmamux1 94 0x400 0x01>;
+				dma-names = "rx", "rx-ctrl";
+				access-controllers = <&etzpc 29>;
+				status = "disabled";
+			};
+
+			usart2: serial@4000e000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x4000e000 0x400>;
+				interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART2_K>;
+				wakeup-source;
+				dmas = <&dmamux1 43 0x400 0x15>,
+				       <&dmamux1 44 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 30>;
+				status = "disabled";
+			};
+
+			usart3: serial@4000f000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x4000f000 0x400>;
+				interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART3_K>;
+				wakeup-source;
+				dmas = <&dmamux1 45 0x400 0x15>,
+				       <&dmamux1 46 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 31>;
+				status = "disabled";
+			};
+
+			uart4: serial@40010000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40010000 0x400>;
+				interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART4_K>;
+				wakeup-source;
+				dmas = <&dmamux1 63 0x400 0x15>,
+				       <&dmamux1 64 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 32>;
+				status = "disabled";
+			};
+
+			uart5: serial@40011000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40011000 0x400>;
+				interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART5_K>;
+				wakeup-source;
+				dmas = <&dmamux1 65 0x400 0x15>,
+				       <&dmamux1 66 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 33>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@40012000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40012000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C1_K>;
+				resets = <&rcc I2C1_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x1>;
+				wakeup-source;
+				i2c-analog-filter;
+				access-controllers = <&etzpc 34>;
 				status = "disabled";
 			};
-			timer@15 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <15>;
+
+			i2c2: i2c@40013000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40013000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C2_K>;
+				resets = <&rcc I2C2_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x2>;
+				wakeup-source;
+				i2c-analog-filter;
+				access-controllers = <&etzpc 35>;
 				status = "disabled";
 			};
-		};
 
-		timers17: timer@44008000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44008000 0x400>;
-			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM17_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 111 0x400 0x1>,
-			       <&dmamux1 112 0x400 0x1>;
-			dma-names = "ch1", "up";
-			status = "disabled";
+			i2c3: i2c@40014000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40014000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C3_K>;
+				resets = <&rcc I2C3_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x4>;
+				wakeup-source;
+				i2c-analog-filter;
+				access-controllers = <&etzpc 36>;
+				status = "disabled";
+			};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
+			i2c5: i2c@40015000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40015000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C5_K>;
+				resets = <&rcc I2C5_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x10>;
+				wakeup-source;
+				i2c-analog-filter;
+				access-controllers = <&etzpc 37>;
 				status = "disabled";
 			};
 
-			timer@16 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <16>;
+			cec: cec@40016000 {
+				compatible = "st,stm32-cec";
+				reg = <0x40016000 0x400>;
+				interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc CEC_K>, <&rcc CEC>;
+				clock-names = "cec", "hdmi-cec";
+				access-controllers = <&etzpc 38>;
 				status = "disabled";
 			};
-		};
 
-		spi5: spi@44009000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x44009000 0x400>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI5_K>;
-			resets = <&rcc SPI5_R>;
-			dmas = <&dmamux1 85 0x400 0x05>,
-			       <&dmamux1 86 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			dac: dac@40017000 {
+				compatible = "st,stm32h7-dac-core";
+				reg = <0x40017000 0x400>;
+				clocks = <&rcc DAC12>;
+				clock-names = "pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				access-controllers = <&etzpc 39>;
+				status = "disabled";
 
-		sai1: sai@4400a000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x4400a000 0x400>;
-			reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
-			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI1_R>;
-			status = "disabled";
+				dac1: dac@1 {
+					compatible = "st,stm32-dac";
+					#io-channel-cells = <1>;
+					reg = <1>;
+					status = "disabled";
+				};
 
-			sai1a: audio-controller@4400a004 {
-				#sound-dai-cells = <0>;
+				dac2: dac@2 {
+					compatible = "st,stm32-dac";
+					#io-channel-cells = <1>;
+					reg = <2>;
+					status = "disabled";
+				};
+			};
 
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x20>;
-				clocks = <&rcc SAI1_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 87 0x400 0x01>;
+			uart7: serial@40018000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40018000 0x400>;
+				interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART7_K>;
+				wakeup-source;
+				dmas = <&dmamux1 79 0x400 0x15>,
+				       <&dmamux1 80 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 40>;
 				status = "disabled";
 			};
 
-			sai1b: audio-controller@4400a024 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI1_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 88 0x400 0x01>;
+			uart8: serial@40019000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40019000 0x400>;
+				interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART8_K>;
+				wakeup-source;
+				dmas = <&dmamux1 81 0x400 0x15>,
+				       <&dmamux1 82 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 41>;
 				status = "disabled";
 			};
-		};
 
-		sai2: sai@4400b000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x4400b000 0x400>;
-			reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
-			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI2_R>;
-			status = "disabled";
+			timers1: timer@44000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44000000 0x400>;
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "brk", "up", "trg-com", "cc";
+				clocks = <&rcc TIM1_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 11 0x400 0x1>,
+				       <&dmamux1 12 0x400 0x1>,
+				       <&dmamux1 13 0x400 0x1>,
+				       <&dmamux1 14 0x400 0x1>,
+				       <&dmamux1 15 0x400 0x1>,
+				       <&dmamux1 16 0x400 0x1>,
+				       <&dmamux1 17 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4",
+					    "up", "trig", "com";
+				access-controllers = <&etzpc 48>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			sai2a: audio-controller@4400b004 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x20>;
-				clocks = <&rcc SAI2_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 89 0x400 0x01>;
-				status = "disabled";
-			};
+				timer@0 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <0>;
+					status = "disabled";
+				};
 
-			sai2b: audio-controller@4400b024 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI2_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 90 0x400 0x01>;
-				status = "disabled";
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
 			};
-		};
 
-		sai3: sai@4400c000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x4400c000 0x400>;
-			reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>;
-			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI3_R>;
-			status = "disabled";
+			timers8: timer@44001000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44001000 0x400>;
+				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "brk", "up", "trg-com", "cc";
+				clocks = <&rcc TIM8_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 47 0x400 0x1>,
+				       <&dmamux1 48 0x400 0x1>,
+				       <&dmamux1 49 0x400 0x1>,
+				       <&dmamux1 50 0x400 0x1>,
+				       <&dmamux1 51 0x400 0x1>,
+				       <&dmamux1 52 0x400 0x1>,
+				       <&dmamux1 53 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4",
+					    "up", "trig", "com";
+				access-controllers = <&etzpc 49>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			sai3a: audio-controller@4400c004 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x20>;
-				clocks = <&rcc SAI3_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 113 0x400 0x01>;
+				timer@7 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <7>;
+					status = "disabled";
+				};
+
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
+
+			usart6: serial@44003000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x44003000 0x400>;
+				interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART6_K>;
+				wakeup-source;
+				dmas = <&dmamux1 71 0x400 0x15>,
+				<&dmamux1 72 0x400 0x11>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 51>;
 				status = "disabled";
 			};
 
-			sai3b: audio-controller@4400c024 {
+			i2s1: audio-controller@44004000 {
+				compatible = "st,stm32h7-i2s";
 				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI3_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 114 0x400 0x01>;
+				reg = <0x44004000 0x400>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 37 0x400 0x01>,
+				<&dmamux1 38 0x400 0x01>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 52>;
 				status = "disabled";
 			};
-		};
-
-		dfsdm: dfsdm@4400d000 {
-			compatible = "st,stm32mp1-dfsdm";
-			reg = <0x4400d000 0x800>;
-			clocks = <&rcc DFSDM_K>;
-			clock-names = "dfsdm";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
 
-			dfsdm0: filter@0 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <0>;
-				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 101 0x400 0x01>;
-				dma-names = "rx";
+			spi1: spi@44004000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x44004000 0x400>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI1_K>;
+				resets = <&rcc SPI1_R>;
+				dmas = <&dmamux1 37 0x400 0x05>,
+				<&dmamux1 38 0x400 0x05>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 52>;
 				status = "disabled";
 			};
 
-			dfsdm1: filter@1 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <1>;
-				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 102 0x400 0x01>;
-				dma-names = "rx";
+			spi4: spi@44005000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x44005000 0x400>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI4_K>;
+				resets = <&rcc SPI4_R>;
+				dmas = <&dmamux1 83 0x400 0x05>,
+				<&dmamux1 84 0x400 0x05>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 53>;
 				status = "disabled";
 			};
 
-			dfsdm2: filter@2 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <2>;
-				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 103 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+			timers15: timer@44006000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44006000 0x400>;
+				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM15_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 105 0x400 0x1>,
+				       <&dmamux1 106 0x400 0x1>,
+				       <&dmamux1 107 0x400 0x1>,
+				       <&dmamux1 108 0x400 0x1>;
+				dma-names = "ch1", "up", "trig", "com";
+				access-controllers = <&etzpc 54>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@14 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <14>;
+					status = "disabled";
+				};
 			};
 
-			dfsdm3: filter@3 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <3>;
-				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 104 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+			timers16: timer@44007000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44007000 0x400>;
+				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM16_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 109 0x400 0x1>,
+				<&dmamux1 110 0x400 0x1>;
+				dma-names = "ch1", "up";
+				access-controllers = <&etzpc 55>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+				timer@15 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <15>;
+					status = "disabled";
+				};
 			};
 
-			dfsdm4: filter@4 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <4>;
-				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 91 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+			timers17: timer@44008000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44008000 0x400>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM17_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 111 0x400 0x1>,
+				<&dmamux1 112 0x400 0x1>;
+				dma-names = "ch1", "up";
+				access-controllers = <&etzpc 56>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@16 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <16>;
+					status = "disabled";
+				};
 			};
 
-			dfsdm5: filter@5 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <5>;
-				interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 92 0x400 0x01>;
-				dma-names = "rx";
+			spi5: spi@44009000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x44009000 0x400>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI5_K>;
+				resets = <&rcc SPI5_R>;
+				dmas = <&dmamux1 85 0x400 0x05>,
+				<&dmamux1 86 0x400 0x05>;
+				dma-names = "rx", "tx";
+				access-controllers = <&etzpc 57>;
 				status = "disabled";
 			};
-		};
 
-		dma1: dma-controller@48000000 {
-			compatible = "st,stm32-dma";
-			reg = <0x48000000 0x400>;
-			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc DMA1>;
-			resets = <&rcc DMA1_R>;
-			#dma-cells = <4>;
-			st,mem2mem;
-			dma-requests = <8>;
-		};
+			sai1: sai@4400a000 {
+				compatible = "st,stm32h7-sai";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x4400a000 0x400>;
+				reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI1_R>;
+				access-controllers = <&etzpc 58>;
+				status = "disabled";
+
+				sai1a: audio-controller@4400a004 {
+					#sound-dai-cells = <0>;
+
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x4 0x20>;
+					clocks = <&rcc SAI1_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 87 0x400 0x01>;
+					status = "disabled";
+				};
 
-		dma2: dma-controller@48001000 {
-			compatible = "st,stm32-dma";
-			reg = <0x48001000 0x400>;
-			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc DMA2>;
-			resets = <&rcc DMA2_R>;
-			#dma-cells = <4>;
-			st,mem2mem;
-			dma-requests = <8>;
-		};
+				sai1b: audio-controller@4400a024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI1_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 88 0x400 0x01>;
+					status = "disabled";
+				};
+			};
 
-		dmamux1: dma-router@48002000 {
-			compatible = "st,stm32h7-dmamux";
-			reg = <0x48002000 0x40>;
-			#dma-cells = <3>;
-			dma-requests = <128>;
-			dma-masters = <&dma1 &dma2>;
-			dma-channels = <16>;
-			clocks = <&rcc DMAMUX>;
-			resets = <&rcc DMAMUX_R>;
-		};
+			sai2: sai@4400b000 {
+				compatible = "st,stm32h7-sai";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x4400b000 0x400>;
+				reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
+				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI2_R>;
+				access-controllers = <&etzpc 59>;
+				status = "disabled";
+
+				sai2a: audio-controller@4400b004 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x4 0x20>;
+					clocks = <&rcc SAI2_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 89 0x400 0x01>;
+					status = "disabled";
+				};
 
-		adc: adc@48003000 {
-			compatible = "st,stm32mp1-adc-core";
-			reg = <0x48003000 0x400>;
-			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc ADC12>, <&rcc ADC12_K>;
-			clock-names = "bus", "adc";
-			interrupt-controller;
-			st,syscfg = <&syscfg>;
-			#interrupt-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
+				sai2b: audio-controller@4400b024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI2_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 90 0x400 0x01>;
+					status = "disabled";
+				};
+			};
 
-			adc1: adc@0 {
-				compatible = "st,stm32mp1-adc";
-				#io-channel-cells = <1>;
+			sai3: sai@4400c000 {
+				compatible = "st,stm32h7-sai";
 				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x0>;
-				interrupt-parent = <&adc>;
-				interrupts = <0>;
-				dmas = <&dmamux1 9 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+				#size-cells = <1>;
+				ranges = <0 0x4400c000 0x400>;
+				reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI3_R>;
+				access-controllers = <&etzpc 60>;
+				status = "disabled";
+
+				sai3a: audio-controller@4400c004 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x04 0x20>;
+					clocks = <&rcc SAI3_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 113 0x400 0x01>;
+					status = "disabled";
+				};
+
+				sai3b: audio-controller@4400c024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI3_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 114 0x400 0x01>;
+					status = "disabled";
+				};
 			};
 
-			adc2: adc@100 {
-				compatible = "st,stm32mp1-adc";
-				#io-channel-cells = <1>;
+			dfsdm: dfsdm@4400d000 {
+				compatible = "st,stm32mp1-dfsdm";
+				reg = <0x4400d000 0x800>;
+				clocks = <&rcc DFSDM_K>;
+				clock-names = "dfsdm";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				reg = <0x100>;
-				interrupt-parent = <&adc>;
-				interrupts = <1>;
-				dmas = <&dmamux1 10 0x400 0x01>;
-				dma-names = "rx";
-				nvmem-cells = <&vrefint>;
-				nvmem-cell-names = "vrefint";
-				status = "disabled";
-				channel@13 {
-					reg = <13>;
-					label = "vrefint";
+				access-controllers = <&etzpc 61>;
+				status = "disabled";
+
+				dfsdm0: filter@0 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <0>;
+					interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 101 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
 				};
-				channel@14 {
-					reg = <14>;
-					label = "vddcore";
+
+				dfsdm1: filter@1 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <1>;
+					interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 102 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
 				};
-			};
-		};
 
-		sdmmc3: mmc@48004000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
-			reg = <0x48004000 0x400>;
-			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC3_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC3_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
+				dfsdm2: filter@2 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <2>;
+					interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 103 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-		usbotg_hs: usb-otg@49000000 {
-			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
-			reg = <0x49000000 0x10000>;
-			clocks = <&rcc USBO_K>, <&usbphyc>;
-			clock-names = "otg", "utmi";
-			resets = <&rcc USBO_R>;
-			reset-names = "dwc2";
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			g-rx-fifo-size = <512>;
-			g-np-tx-fifo-size = <32>;
-			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
-			dr_mode = "otg";
-			otg-rev = <0x200>;
-			usb33d-supply = <&usb33>;
-			status = "disabled";
-		};
-
-		ipcc: mailbox@4c001000 {
-			compatible = "st,stm32mp1-ipcc";
-			#mbox-cells = <1>;
-			reg = <0x4c001000 0x400>;
-			st,proc-id = <0>;
-			interrupts-extended =
-				<&exti 61 1>,
-				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "rx", "tx";
-			clocks = <&rcc IPCC>;
-			wakeup-source;
-			status = "disabled";
-		};
-
-		dcmi: dcmi@4c006000 {
-			compatible = "st,stm32-dcmi";
-			reg = <0x4c006000 0x400>;
-			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc CAMITF_R>;
-			clocks = <&rcc DCMI>;
-			clock-names = "mclk";
-			dmas = <&dmamux1 75 0x400 0x01>;
-			dma-names = "tx";
-			status = "disabled";
-		};
-
-		rcc: rcc@50000000 {
-			compatible = "st,stm32mp1-rcc", "syscon";
-			reg = <0x50000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
+				dfsdm3: filter@3 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <3>;
+					interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 104 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-		pwr_regulators: pwr@50001000 {
-			compatible = "st,stm32mp1,pwr-reg";
-			reg = <0x50001000 0x10>;
+				dfsdm4: filter@4 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <4>;
+					interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 91 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-			reg11: reg11 {
-				regulator-name = "reg11";
-				regulator-min-microvolt = <1100000>;
-				regulator-max-microvolt = <1100000>;
+				dfsdm5: filter@5 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <5>;
+					interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 92 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 			};
 
-			reg18: reg18 {
-				regulator-name = "reg18";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
+			dma1: dma-controller@48000000 {
+				compatible = "st,stm32-dma";
+				reg = <0x48000000 0x400>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc DMA1>;
+				resets = <&rcc DMA1_R>;
+				#dma-cells = <4>;
+				st,mem2mem;
+				dma-requests = <8>;
+				access-controllers = <&etzpc 88>;
+			};
+
+			dma2: dma-controller@48001000 {
+				compatible = "st,stm32-dma";
+				reg = <0x48001000 0x400>;
+				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc DMA2>;
+				resets = <&rcc DMA2_R>;
+				#dma-cells = <4>;
+				st,mem2mem;
+				dma-requests = <8>;
+				access-controllers = <&etzpc 89>;
+			};
+
+			dmamux1: dma-router@48002000 {
+				compatible = "st,stm32h7-dmamux";
+				reg = <0x48002000 0x40>;
+				#dma-cells = <3>;
+				dma-requests = <128>;
+				dma-masters = <&dma1 &dma2>;
+				dma-channels = <16>;
+				clocks = <&rcc DMAMUX>;
+				resets = <&rcc DMAMUX_R>;
+				access-controllers = <&etzpc 90>;
+			};
+
+			adc: adc@48003000 {
+				compatible = "st,stm32mp1-adc-core";
+				reg = <0x48003000 0x400>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc ADC12>, <&rcc ADC12_K>;
+				clock-names = "bus", "adc";
+				interrupt-controller;
+				st,syscfg = <&syscfg>;
+				#interrupt-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				access-controllers = <&etzpc 72>;
+				status = "disabled";
+
+				adc1: adc@0 {
+					compatible = "st,stm32mp1-adc";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+					interrupt-parent = <&adc>;
+					interrupts = <0>;
+					dmas = <&dmamux1 9 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-			usb33: usb33 {
-				regulator-name = "usb33";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
+				adc2: adc@100 {
+					compatible = "st,stm32mp1-adc";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x100>;
+					interrupt-parent = <&adc>;
+					interrupts = <1>;
+					dmas = <&dmamux1 10 0x400 0x01>;
+					dma-names = "rx";
+					nvmem-cells = <&vrefint>;
+					nvmem-cell-names = "vrefint";
+					status = "disabled";
+					channel@13 {
+						reg = <13>;
+						label = "vrefint";
+					};
+					channel@14 {
+						reg = <14>;
+						label = "vddcore";
+					};
+				};
 			};
-		};
 
-		pwr_mcu: pwr_mcu@50001014 {
-			compatible = "st,stm32mp151-pwr-mcu", "syscon";
-			reg = <0x50001014 0x4>;
-		};
+			sdmmc3: mmc@48004000 {
+				compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00253180>;
+				reg = <0x48004000 0x400>;
+				interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SDMMC3_K>;
+				clock-names = "apb_pclk";
+				resets = <&rcc SDMMC3_R>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <120000000>;
+				access-controllers = <&etzpc 86>;
+				status = "disabled";
+			};
+
+			usbotg_hs: usb-otg@49000000 {
+				compatible = "st,stm32mp15-hsotg", "snps,dwc2";
+				reg = <0x49000000 0x10000>;
+				clocks = <&rcc USBO_K>, <&usbphyc>;
+				clock-names = "otg", "utmi";
+				resets = <&rcc USBO_R>;
+				reset-names = "dwc2";
+				interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+				g-rx-fifo-size = <512>;
+				g-np-tx-fifo-size = <32>;
+				g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
+				dr_mode = "otg";
+				otg-rev = <0x200>;
+				usb33d-supply = <&usb33>;
+				access-controllers = <&etzpc 85>;
+				status = "disabled";
+			};
+
+			dcmi: dcmi@4c006000 {
+				compatible = "st,stm32-dcmi";
+				reg = <0x4c006000 0x400>;
+				interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc CAMITF_R>;
+				clocks = <&rcc DCMI>;
+				clock-names = "mclk";
+				dmas = <&dmamux1 75 0x400 0x01>;
+				dma-names = "tx";
+				access-controllers = <&etzpc 70>;
+				status = "disabled";
+			};
+
+			lptimer2: timer@50021000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x50021000 0x400>;
+				interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM2_K>;
+				clock-names = "mux";
+				wakeup-source;
+				access-controllers = <&etzpc 64>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		exti: interrupt-controller@5000d000 {
-			compatible = "st,stm32mp1-exti", "syscon";
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			reg = <0x5000d000 0x400>;
-		};
+				trigger@1 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <1>;
+					status = "disabled";
+				};
 
-		syscfg: syscon@50020000 {
-			compatible = "st,stm32mp157-syscfg", "syscon";
-			reg = <0x50020000 0x400>;
-			clocks = <&rcc SYSCFG>;
-		};
+				counter {
+					compatible = "st,stm32-lptimer-counter";
+					status = "disabled";
+				};
+			};
 
-		lptimer2: timer@50021000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x50021000 0x400>;
-			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM2_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
+			lptimer3: timer@50022000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x50022000 0x400>;
+				interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM3_K>;
+				clock-names = "mux";
+				wakeup-source;
+				access-controllers = <&etzpc 65>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
+				trigger@2 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <2>;
+					status = "disabled";
+				};
 			};
 
-			trigger@1 {
-				compatible = "st,stm32-lptimer-trigger";
-				reg = <1>;
+			lptimer4: timer@50023000 {
+				compatible = "st,stm32-lptimer";
+				reg = <0x50023000 0x400>;
+				interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM4_K>;
+				clock-names = "mux";
+				wakeup-source;
+				access-controllers = <&etzpc 66>;
 				status = "disabled";
-			};
 
-			counter {
-				compatible = "st,stm32-lptimer-counter";
-				status = "disabled";
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 			};
-		};
-
-		lptimer3: timer@50022000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x50022000 0x400>;
-			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM3_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
+			lptimer5: timer@50024000 {
+				compatible = "st,stm32-lptimer";
+				reg = <0x50024000 0x400>;
+				interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM5_K>;
+				clock-names = "mux";
+				wakeup-source;
+				access-controllers = <&etzpc 67>;
 				status = "disabled";
-			};
 
-			trigger@2 {
-				compatible = "st,stm32-lptimer-trigger";
-				reg = <2>;
-				status = "disabled";
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 			};
-		};
-
-		lptimer4: timer@50023000 {
-			compatible = "st,stm32-lptimer";
-			reg = <0x50023000 0x400>;
-			interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM4_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
+			vrefbuf: vrefbuf@50025000 {
+				compatible = "st,stm32-vrefbuf";
+				reg = <0x50025000 0x8>;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2500000>;
+				clocks = <&rcc VREF>;
+				access-controllers = <&etzpc 69>;
 				status = "disabled";
 			};
-		};
 
-		lptimer5: timer@50024000 {
-			compatible = "st,stm32-lptimer";
-			reg = <0x50024000 0x400>;
-			interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM5_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
+			sai4: sai@50027000 {
+				compatible = "st,stm32h7-sai";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x50027000 0x400>;
+				reg = <0x50027000 0x4>, <0x500273f0 0x10>;
+				interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI4_R>;
+				access-controllers = <&etzpc 68>;
+				status = "disabled";
+
+				sai4a: audio-controller@50027004 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x04 0x20>;
+					clocks = <&rcc SAI4_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 99 0x400 0x01>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
+				sai4b: audio-controller@50027024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI4_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 100 0x400 0x01>;
+					status = "disabled";
+				};
 			};
-		};
 
-		vrefbuf: vrefbuf@50025000 {
-			compatible = "st,stm32-vrefbuf";
-			reg = <0x50025000 0x8>;
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <2500000>;
-			clocks = <&rcc VREF>;
-			status = "disabled";
-		};
-
-		sai4: sai@50027000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x50027000 0x400>;
-			reg = <0x50027000 0x4>, <0x500273f0 0x10>;
-			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI4_R>;
-			status = "disabled";
+			hash1: hash@54002000 {
+				compatible = "st,stm32f756-hash";
+				reg = <0x54002000 0x400>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc HASH1>;
+				resets = <&rcc HASH1_R>;
+				dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
+				dma-names = "in";
+				dma-maxburst = <2>;
+				access-controllers = <&etzpc 8>;
+				status = "disabled";
+			};
+
+			rng1: rng@54003000 {
+				compatible = "st,stm32-rng";
+				reg = <0x54003000 0x400>;
+				clocks = <&rcc RNG1_K>;
+				resets = <&rcc RNG1_R>;
+				access-controllers = <&etzpc 7>;
+				status = "okay";
+			};
+
+			fmc: memory-controller@58002000 {
+				#address-cells = <2>;
+				#size-cells = <1>;
+				compatible = "st,stm32mp1-fmc2-ebi";
+				reg = <0x58002000 0x1000>;
+				clocks = <&rcc FMC_K>;
+				resets = <&rcc FMC_R>;
+				access-controllers = <&etzpc 91>;
+				status = "disabled";
+
+				ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+					 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+					 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+					 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+					 <4 0 0x80000000 0x10000000>; /* NAND */
+
+				nand-controller@4,0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "st,stm32mp1-fmc2-nfc";
+					reg = <4 0x00000000 0x1000>,
+					      <4 0x08010000 0x1000>,
+					      <4 0x08020000 0x1000>,
+					      <4 0x01000000 0x1000>,
+					      <4 0x09010000 0x1000>,
+					      <4 0x09020000 0x1000>;
+					interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+					       <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+					       <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+					dma-names = "tx", "rx", "ecc";
+					status = "disabled";
+				};
+			};
 
-			sai4a: audio-controller@50027004 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x20>;
-				clocks = <&rcc SAI4_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 99 0x400 0x01>;
-				status = "disabled";
+			qspi: spi@58003000 {
+				compatible = "st,stm32f469-qspi";
+				reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+				reg-names = "qspi", "qspi_mm";
+				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
+				       <&mdma1 22 0x2 0x10100008 0x0 0x0>;
+				dma-names = "tx", "rx";
+				clocks = <&rcc QSPI_K>;
+				resets = <&rcc QSPI_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				access-controllers = <&etzpc 92>;
+				status = "disabled";
+			};
+
+			ethernet0: ethernet@5800a000 {
+				compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
+				reg = <0x5800a000 0x2000>;
+				reg-names = "stmmaceth";
+				interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "macirq";
+				clock-names = "stmmaceth",
+					      "mac-clk-tx",
+					      "mac-clk-rx",
+					      "eth-ck",
+					      "ptp_ref",
+					      "ethstp";
+				clocks = <&rcc ETHMAC>,
+					 <&rcc ETHTX>,
+					 <&rcc ETHRX>,
+					 <&rcc ETHCK_K>,
+					 <&rcc ETHPTP_K>,
+					 <&rcc ETHSTP>;
+				st,syscon = <&syscfg 0x4>;
+				snps,mixed-burst;
+				snps,pbl = <2>;
+				snps,en-tx-lpi-clockgating;
+				snps,axi-config = <&stmmac_axi_config_0>;
+				snps,tso;
+				access-controllers = <&etzpc 94>;
+				status = "disabled";
+
+				stmmac_axi_config_0: stmmac-axi-config {
+					snps,wr_osr_lmt = <0x7>;
+					snps,rd_osr_lmt = <0x7>;
+					snps,blen = <0 0 0 0 16 8 4>;
+				};
 			};
 
-			sai4b: audio-controller@50027024 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI4_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 100 0x400 0x01>;
+			usart1: serial@5c000000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x5c000000 0x400>;
+				interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART1_K>;
+				wakeup-source;
+				access-controllers = <&etzpc 3>;
 				status = "disabled";
 			};
-		};
-
-		dts: thermal@50028000 {
-			compatible = "st,stm32-thermal";
-			reg = <0x50028000 0x100>;
-			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc TMPSENS>;
-			clock-names = "pclk";
-			#thermal-sensor-cells = <0>;
-			status = "disabled";
-		};
-
-		hash1: hash@54002000 {
-			compatible = "st,stm32f756-hash";
-			reg = <0x54002000 0x400>;
-			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc HASH1>;
-			resets = <&rcc HASH1_R>;
-			dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
-			dma-names = "in";
-			dma-maxburst = <2>;
-			status = "disabled";
-		};
-
-		rng1: rng@54003000 {
-			compatible = "st,stm32-rng";
-			reg = <0x54003000 0x400>;
-			clocks = <&rcc RNG1_K>;
-			resets = <&rcc RNG1_R>;
-			status = "disabled";
-		};
 
-		mdma1: dma-controller@58000000 {
-			compatible = "st,stm32h7-mdma";
-			reg = <0x58000000 0x1000>;
-			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc MDMA>;
-			resets = <&rcc MDMA_R>;
-			#dma-cells = <5>;
-			dma-channels = <32>;
-			dma-requests = <48>;
-		};
-
-		fmc: memory-controller@58002000 {
-			#address-cells = <2>;
-			#size-cells = <1>;
-			compatible = "st,stm32mp1-fmc2-ebi";
-			reg = <0x58002000 0x1000>;
-			clocks = <&rcc FMC_K>;
-			resets = <&rcc FMC_R>;
-			status = "disabled";
-
-			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
-				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
-				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
-				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
-				 <4 0 0x80000000 0x10000000>; /* NAND */
-
-			nand-controller@4,0 {
+			spi6: spi@5c001000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x5c001000 0x400>;
+				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI6_K>;
+				resets = <&rcc SPI6_R>;
+				dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
+				       <&mdma1 35 0x0 0x40002 0x0 0x0>;
+				access-controllers = <&etzpc 4>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			i2c4: i2c@5c002000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x5c002000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C4_K>;
+				resets = <&rcc I2C4_R>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "st,stm32mp1-fmc2-nfc";
-				reg = <4 0x00000000 0x1000>,
-				      <4 0x08010000 0x1000>,
-				      <4 0x08020000 0x1000>,
-				      <4 0x01000000 0x1000>,
-				      <4 0x09010000 0x1000>,
-				      <4 0x09020000 0x1000>;
-				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
-				       <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
-				       <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
-				dma-names = "tx", "rx", "ecc";
+				st,syscfg-fmp = <&syscfg 0x4 0x8>;
+				wakeup-source;
+				i2c-analog-filter;
+				access-controllers = <&etzpc 5>;
 				status = "disabled";
 			};
-		};
-
-		qspi: spi@58003000 {
-			compatible = "st,stm32f469-qspi";
-			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
-			reg-names = "qspi", "qspi_mm";
-			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
-			       <&mdma1 22 0x2 0x10100008 0x0 0x0>;
-			dma-names = "tx", "rx";
-			clocks = <&rcc QSPI_K>;
-			resets = <&rcc QSPI_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		sdmmc1: mmc@58005000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
-			reg = <0x58005000 0x1000>;
-			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC1_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC1_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		sdmmc2: mmc@58007000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
-			reg = <0x58007000 0x1000>;
-			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC2_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC2_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		crc1: crc@58009000 {
-			compatible = "st,stm32f7-crc";
-			reg = <0x58009000 0x400>;
-			clocks = <&rcc CRC1>;
-			status = "disabled";
-		};
-
-		ethernet0: ethernet@5800a000 {
-			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
-			reg = <0x5800a000 0x2000>;
-			reg-names = "stmmaceth";
-			interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "macirq";
-			clock-names = "stmmaceth",
-				      "mac-clk-tx",
-				      "mac-clk-rx",
-				      "eth-ck",
-				      "ptp_ref",
-				      "ethstp";
-			clocks = <&rcc ETHMAC>,
-				 <&rcc ETHTX>,
-				 <&rcc ETHRX>,
-				 <&rcc ETHCK_K>,
-				 <&rcc ETHPTP_K>,
-				 <&rcc ETHSTP>;
-			st,syscon = <&syscfg 0x4>;
-			snps,mixed-burst;
-			snps,pbl = <2>;
-			snps,en-tx-lpi-clockgating;
-			snps,axi-config = <&stmmac_axi_config_0>;
-			snps,tso;
-			status = "disabled";
-
-			stmmac_axi_config_0: stmmac-axi-config {
-				snps,wr_osr_lmt = <0x7>;
-				snps,rd_osr_lmt = <0x7>;
-				snps,blen = <0 0 0 0 16 8 4>;
-			};
-		};
-
-		usbh_ohci: usb@5800c000 {
-			compatible = "generic-ohci";
-			reg = <0x5800c000 0x1000>;
-			clocks = <&usbphyc>, <&rcc USBH>;
-			resets = <&rcc USBH_R>;
-			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
 
-		usbh_ehci: usb@5800d000 {
-			compatible = "generic-ehci";
-			reg = <0x5800d000 0x1000>;
-			clocks = <&usbphyc>, <&rcc USBH>;
-			resets = <&rcc USBH_R>;
-			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-			companion = <&usbh_ohci>;
-			status = "disabled";
-		};
-
-		ltdc: display-controller@5a001000 {
-			compatible = "st,stm32-ltdc";
-			reg = <0x5a001000 0x400>;
-			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LTDC_PX>;
-			clock-names = "lcd";
-			resets = <&rcc LTDC_R>;
-			status = "disabled";
-		};
-
-		iwdg2: watchdog@5a002000 {
-			compatible = "st,stm32mp1-iwdg";
-			reg = <0x5a002000 0x400>;
-			clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
-			clock-names = "pclk", "lsi";
-			status = "disabled";
-		};
-
-		usbphyc: usbphyc@5a006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			#clock-cells = <0>;
-			compatible = "st,stm32mp1-usbphyc";
-			reg = <0x5a006000 0x1000>;
-			clocks = <&rcc USBPHY_K>;
-			resets = <&rcc USBPHY_R>;
-			vdda1v1-supply = <&reg11>;
-			vdda1v8-supply = <&reg18>;
-			status = "disabled";
-
-			usbphyc_port0: usb-phy@0 {
-				#phy-cells = <0>;
-				reg = <0>;
-			};
-
-			usbphyc_port1: usb-phy@1 {
-				#phy-cells = <1>;
-				reg = <1>;
-			};
-		};
-
-		usart1: serial@5c000000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x5c000000 0x400>;
-			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART1_K>;
-			wakeup-source;
-			status = "disabled";
-		};
-
-		spi6: spi@5c001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x5c001000 0x400>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI6_K>;
-			resets = <&rcc SPI6_R>;
-			dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
-			       <&mdma1 35 0x0 0x40002 0x0 0x0>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		i2c4: i2c@5c002000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x5c002000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C4_K>;
-			resets = <&rcc I2C4_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x8>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
-		rtc: rtc@5c004000 {
-			compatible = "st,stm32mp1-rtc";
-			reg = <0x5c004000 0x400>;
-			clocks = <&rcc RTCAPB>, <&rcc RTC>;
-			clock-names = "pclk", "rtc_ck";
-			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		bsec: efuse@5c005000 {
-			compatible = "st,stm32mp15-bsec";
-			reg = <0x5c005000 0x400>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			part_number_otp: part-number-otp@4 {
-				reg = <0x4 0x1>;
-			};
-			vrefint: vrefin-cal@52 {
-				reg = <0x52 0x2>;
-			};
-			ts_cal1: calib@5c {
-				reg = <0x5c 0x2>;
-			};
-			ts_cal2: calib@5e {
-				reg = <0x5e 0x2>;
+			i2c6: i2c@5c009000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x5c009000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C6_K>;
+				resets = <&rcc I2C6_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x20>;
+				wakeup-source;
+				i2c-analog-filter;
+				access-controllers = <&etzpc 12>;
+				status = "disabled";
 			};
 		};
 
-		i2c6: i2c@5c009000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x5c009000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C6_K>;
-			resets = <&rcc I2C6_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x20>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
 		tamp: tamp@5c00a000 {
 			compatible = "st,stm32-tamp", "syscon", "simple-mfd";
 			reg = <0x5c00a000 0x400>;
diff --git a/arch/arm/boot/dts/st/stm32mp153.dtsi b/arch/arm/boot/dts/st/stm32mp153.dtsi
index 486084e0b80b..4640dafb1598 100644
--- a/arch/arm/boot/dts/st/stm32mp153.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp153.dtsi
@@ -28,32 +28,34 @@  timer {
 			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+};
 
-	soc {
-		m_can1: can@4400e000 {
-			compatible = "bosch,m_can";
-			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
-			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
-			status = "disabled";
-		};
+&etzpc {
+	m_can1: can@4400e000 {
+		compatible = "bosch,m_can";
+		reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
+		reg-names = "m_can", "message_ram";
+		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+		clock-names = "hclk", "cclk";
+		bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+		access-controllers = <&etzpc 62>;
+		status = "disabled";
+	};
 
-		m_can2: can@4400f000 {
-			compatible = "bosch,m_can";
-			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
-			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
-			status = "disabled";
-		};
+	m_can2: can@4400f000 {
+		compatible = "bosch,m_can";
+		reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
+		reg-names = "m_can", "message_ram";
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+		clock-names = "hclk", "cclk";
+		bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+		access-controllers = <&etzpc 62>;
+		status = "disabled";
 	};
 };
diff --git a/arch/arm/boot/dts/st/stm32mp15xc.dtsi b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
index b06a55a2fa18..97465717f932 100644
--- a/arch/arm/boot/dts/st/stm32mp15xc.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
@@ -4,15 +4,14 @@ 
  * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
  */
 
-/ {
-	soc {
-		cryp1: cryp@54001000 {
-			compatible = "st,stm32mp1-cryp";
-			reg = <0x54001000 0x400>;
-			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CRYP1>;
-			resets = <&rcc CRYP1_R>;
-			status = "disabled";
-		};
+&etzpc {
+	cryp1: cryp@54001000 {
+		compatible = "st,stm32mp1-cryp";
+		reg = <0x54001000 0x400>;
+		interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CRYP1>;
+		resets = <&rcc CRYP1_R>;
+		access-controllers = <&etzpc 9>;
+		status = "disabled";
 	};
 };