diff mbox series

[2/2] arm64: dts: qcom: add QCM6490 SHIFTphone 8

Message ID 20240508-otter-bringup-v1-2-c807d3d931f6@linaro.org
State Superseded
Headers show
Series qcom: initial support for the SHIFTphone 8 | expand

Commit Message

Caleb Connolly May 7, 2024, 11:28 p.m. UTC
The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following
features:

* 12GB of RAM, 512GB UFS storage
* 1080p display.
* Hardware kill switches for cameras and microphones
* UART access via type-c SBU pins (enabled by an internal switch)

Initial support includes:

* Framebuffer display
* UFS and sdcard storage
* Battery monitoring and USB role switching via pmic glink
* Bluetooth
* Thermals

Wifi is not yet functional due to a crash in the remoteproc
firmware.

Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile                |   1 +
 arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++
 2 files changed, 939 insertions(+)

Comments

Markus Elfring May 8, 2024, 7:51 a.m. UTC | #1
> Initial support includes:
…

How do you think about to use imperative wordings for improved change descriptions?
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/process/submitting-patches.rst?h=v6.9-rc7#n94

Regards,
Markus
Luca Weiss May 10, 2024, 6:24 a.m. UTC | #2
Hi Caleb,

On Wed May 8, 2024 at 1:28 AM CEST, Caleb Connolly wrote:
> The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following
> features:
>
> * 12GB of RAM, 512GB UFS storage
> * 1080p display.
> * Hardware kill switches for cameras and microphones
> * UART access via type-c SBU pins (enabled by an internal switch)
>
> Initial support includes:
>
> * Framebuffer display
> * UFS and sdcard storage
> * Battery monitoring and USB role switching via pmic glink
> * Bluetooth
> * Thermals
>
> Wifi is not yet functional due to a crash in the remoteproc
> firmware.
>
> Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile                |   1 +
>  arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++
>  2 files changed, 939 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 7d40ec5e7d21..678e800ac797 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -92,8 +92,9 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-fairphone-fp5.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-idp.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-shift-otter.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= qdu1000-idp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
> new file mode 100644
> index 000000000000..ceef8b9b2414
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
> @@ -0,0 +1,938 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Based largely on Fairphone 5 DT.

:) But not sure this needs to be in the file, in the commit message
would be enough imo

> + *
> + * Copyright (c) 2023, Luca Weiss <luca.weiss@fairphone.com>
> + * Copyright (c) 2024, Caleb Connolly <caleb.connolly@linaro.org>
> + */
> +
> +/dts-v1/;
> +
> +#define PM7250B_SID 8
> +#define PM7250B_SID1 9
> +
> +#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h>
> +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "sc7280.dtsi"

Sort the list of PMICs by alphabet? Also I guess you can keep the
comments I have in fp5.dts which has the 'real' model of the PMIC

> +#include "pmk8350.dtsi" /* PMK7325 */
> +#include "pm7325.dtsi"
> +#include "pm8350c.dtsi"
> +#include "pm7250b.dtsi"
> +
> +/* There is also a pmr735a */

This thing also exists on FP5 (named SDR-735-*), but I don't think it's
accessible to Linux - or that Linux needs to do anything with it.
Downstream I also didn't see something for it iirc.

> +
> +/delete-node/ &rmtfs_mem;
> +
> +/ {
> +	model = "SHIFT SHIFTphone 8";
> +	compatible = "shift,otter", "qcom,qcm6490";
> +	chassis-type = "handset";
> +
> +	aliases {
> +		serial0 = &uart5;
> +		serial1 = &uart7;
> +	};
> +
> +	chosen {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		stdout-path = "serial0:115200n8";
> +
> +		framebuffer0: framebuffer@a000000 {
> +			compatible = "simple-framebuffer";
> +			reg = <0x0 0xe1000000 0x0 (2400 * 1080 * 4)>;
> +			width = <1080>;
> +			height = <2400>;
> +			stride = <(1080 * 4)>;
> +			format = "a8r8g8b8";
> +			clocks = <&gcc GCC_DISP_HF_AXI_CLK>;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-0 = <&volume_down_default>;
> +		pinctrl-names = "default";
> +
> +		key-volume-up {
> +			label = "Volume up";
> +			gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +			debounce-interval = <15>;
> +		};
> +	};
> +
> +	pmic-glink {
> +		compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink";
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		connector@0 {
> +			compatible = "usb-c-connector";
> +			reg = <0>;
> +			power-role = "dual";
> +			data-role = "dual";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					pmic_glink_hs_in: endpoint {
> +						remote-endpoint = <&usb_1_dwc3_hs>;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					pmic_glink_ss_in: endpoint {
> +						remote-endpoint = <&usb_dp_qmpphy_out>;
> +					};
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					pmic_glink_sbu: endpoint {
> +						remote-endpoint = <&fsa4480_sbu_mux>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	reserved-memory {
> +		cont_splash_mem: cont-splash@e1000000 {
> +			reg = <0x0 0xe1000000 0x0 0x2300000>;
> +			no-map;
> +		};
> +
> +		cdsp_mem: cdsp@88f00000 {
> +			reg = <0x0 0x88f00000 0x0 0x1e00000>;
> +			no-map;
> +		};
> +
> +		rmtfs_mem: memory@f8500000 {

rmtfs@

> +			compatible = "qcom,rmtfs-mem";
> +			reg = <0x0 0xf8500000 0x0 0x600000>;
> +			no-map;
> +
> +			qcom,client-id = <1>;
> +			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>, <QCOM_SCM_VMID_NAV>;
> +		};
> +	};
> +
> +	thermal-zones {
> +		camera-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmk8350_adc_tm 2>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +
> +		chg-skin-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pm7250b_adc_tm 0>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +
> +		conn-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pm7250b_adc_tm 1>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +
> +		quiet-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmk8350_adc_tm 1>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +
> +		rear-cam-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmk8350_adc_tm 4>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +
> +		sdm-skin-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmk8350_adc_tm 3>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +
> +		xo-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmk8350_adc_tm 0>;
> +
> +			trips {
> +				active-config0 {
> +					temperature = <125000>;
> +					hysteresis = <1000>;
> +					type = "passive";
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&apps_rsc {
> +	regulators-0 {
> +		compatible = "qcom,pm7325-rpmh-regulators";
> +		qcom,pmic-id = "b";
> +
> +		vreg_s1b: smps1 {
> +			regulator-min-microvolt = <1840000>;
> +			regulator-max-microvolt = <2040000>;
> +		};
> +
> +		vreg_s7b: smps7 {
> +			regulator-min-microvolt = <535000>;
> +			regulator-max-microvolt = <1120000>;
> +		};
> +
> +		vreg_s8b: smps8 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1500000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
> +		};
> +
> +		vreg_l1b: ldo1 {
> +			regulator-min-microvolt = <825000>;
> +			regulator-max-microvolt = <925000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2b: ldo2 {
> +			regulator-min-microvolt = <2700000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3b: ldo3 {
> +			regulator-min-microvolt = <312000>;
> +			regulator-max-microvolt = <910000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6b: ldo6 {
> +			regulator-min-microvolt = <1140000>;
> +			regulator-max-microvolt = <1260000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7b: ldo7 {
> +			/* Constrained for UFS VCC, at least until UFS driver scales voltage */
> +			regulator-min-microvolt = <2952000>;
> +			regulator-max-microvolt = <2952000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8b: ldo8 {
> +			regulator-min-microvolt = <870000>;
> +			regulator-max-microvolt = <970000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l9b: ldo9 {
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1304000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l11b: ldo11 {
> +			regulator-min-microvolt = <1504000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l12b: ldo12 {
> +			regulator-min-microvolt = <751000>;
> +			regulator-max-microvolt = <824000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13b: ldo13 {
> +			regulator-min-microvolt = <530000>;
> +			regulator-max-microvolt = <824000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l14b: ldo14 {
> +			regulator-min-microvolt = <1080000>;
> +			regulator-max-microvolt = <1304000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l15b: ldo15 {
> +			regulator-min-microvolt = <765000>;
> +			regulator-max-microvolt = <1020000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l16b: ldo16 {
> +			regulator-min-microvolt = <1100000>;
> +			regulator-max-microvolt = <1300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l17b: ldo17 {
> +			regulator-min-microvolt = <1700000>;
> +			regulator-max-microvolt = <1900000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l18b: ldo18 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l19b: ldo19 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-1 {
> +		compatible = "qcom,pm8350c-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		vreg_s1c: smps1 {
> +			regulator-min-microvolt = <2190000>;
> +			regulator-max-microvolt = <2210000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s9c: smps9 {
> +			regulator-min-microvolt = <1010000>;
> +			regulator-max-microvolt = <1170000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l1c: ldo1 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1980000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2c: ldo2 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1950000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3c: ldo3 {
> +			regulator-min-microvolt = <3000000>;
> +			regulator-max-microvolt = <3400000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l4c: ldo4 {
> +			regulator-min-microvolt = <1620000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l5c: ldo5 {
> +			regulator-min-microvolt = <1620000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6c: ldo6 {
> +			regulator-min-microvolt = <1650000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7c: ldo7 {
> +			regulator-min-microvolt = <3000000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8c: ldo8 {
> +			regulator-min-microvolt = <1620000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l9c: ldo9 {
> +			regulator-min-microvolt = <2700000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l10c: ldo10 {
> +			regulator-min-microvolt = <720000>;
> +			regulator-max-microvolt = <1050000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l11c: ldo11 {
> +			regulator-min-microvolt = <2800000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l12c: ldo12 {
> +			regulator-min-microvolt = <1650000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13c: ldo13 {
> +			regulator-min-microvolt = <2700000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_bob: bob {
> +			regulator-min-microvolt = <3008000>;
> +			regulator-max-microvolt = <3960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
> +		};
> +	};
> +};
> +
> +&gcc {
> +	protected-clocks = <GCC_CFG_NOC_LPASS_CLK>,
> +			<GCC_EDP_CLKREF_EN>,
> +			<GCC_MSS_CFG_AHB_CLK>,
> +			<GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>,
> +			<GCC_MSS_OFFLINE_AXI_CLK>,
> +			<GCC_MSS_Q6SS_BOOT_CLK_SRC>,
> +			<GCC_MSS_Q6_MEMNOC_AXI_CLK>,
> +			<GCC_MSS_SNOC_AXI_CLK>,
> +			<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
> +			<GCC_QSPI_CORE_CLK>,
> +			<GCC_QSPI_CORE_CLK_SRC>,
> +			<GCC_SEC_CTRL_CLK_SRC>,
> +			<GCC_WPSS_AHB_BDG_MST_CLK>,
> +			<GCC_WPSS_AHB_CLK>,
> +			<GCC_WPSS_RSCP_CLK>;
> +};
> +
> +&gpi_dma0 {
> +	status = "okay";
> +};
> +
> +&gpi_dma1 {
> +	status = "okay";
> +};
> +
> +&gpu {
> +	status = "okay";
> +};
> +
> +&gpu_zap_shader {
> +	firmware-name = "qcom/qcm6490/SHIFT/otter/a660_zap.mbn";
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +
> +	/* PM8008 PMIC @ 8 and 9 */
> +	/* rtc6226 FM receiver @ 64 */
> +
> +	typec-mux@42 {
> +		compatible = "fcs,fsa4480";
> +		reg = <0x42>;
> +
> +		vcc-supply = <&vreg_bob>;
> +
> +		mode-switch;
> +		orientation-switch;
> +
> +		port {
> +			fsa4480_sbu_mux: endpoint {
> +				remote-endpoint = <&pmic_glink_sbu>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +
> +	/* tas2563 audio codec @ 4d */
> +};
> +
> +&i2c9 {
> +	status = "okay";
> +
> +	/* TMS(?) NFC @ 28 */
> +	/* Ti drv2624 haptics @ 5a */
> +};
> +
> +&i2c13 {
> +	status = "okay";
> +
> +	/* focaltech FT3658U @ 38 */
> +};
> +
> +&ipa {
> +	qcom,gsi-loader = "self";
> +	memory-region = <&ipa_fw_mem>;
> +	firmware-name = "qcom/qcm6490/SHIFT/otter/ipa_fws.mbn";
> +	status = "okay";
> +};
> +
> +&pm7250b_adc {
> +	channel@4d {
> +		reg = <ADC5_AMUX_THM1_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "charger_skin_therm";
> +	};
> +
> +	channel@4f {
> +		reg = <ADC5_AMUX_THM3_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "conn_therm";
> +	};
> +};
> +
> +&pm7250b_adc_tm {
> +	status = "okay";
> +
> +	charger-skin-therm@0 {
> +		reg = <0>;
> +		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +
> +	conn-therm@1 {
> +		reg = <1>;
> +		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +};
> +
> +&pm7325_gpios {
> +	volume_down_default: volume-down-default-state {
> +		pins = "gpio6";
> +		function = PMIC_GPIO_FUNC_NORMAL;
> +		power-source = <1>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +};
> +
> +&pmk8350_adc_tm {
> +	status = "okay";
> +
> +	xo-therm@0 {
> +		reg = <0>;
> +		io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +
> +	quiet-therm@1 {
> +		reg = <1>;
> +		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +
> +	cam-flash-therm@2 {
> +		reg = <2>;
> +		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +
> +	sdm-skin-therm@3 {
> +		reg = <3>;
> +		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +
> +	wide-rfc-therm@4 {
> +		reg = <4>;
> +		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time-us = <200>;
> +	};
> +};
> +
> +&pmk8350_rtc {
> +	status = "okay";
> +};
> +
> +&pmk8350_vadc {
> +	status = "okay";
> +
> +	channel@44 {
> +		reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "pmk8350_xo_therm";
> +	};
> +
> +	channel@144 {
> +		reg = <PM7325_ADC7_AMUX_THM1_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "pm7325_quiet_therm";
> +	};
> +
> +	channel@145 {
> +		reg = <PM7325_ADC7_AMUX_THM2_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "pm7325_cam_flash_therm";
> +	};
> +
> +	channel@146 {
> +		reg = <PM7325_ADC7_AMUX_THM3_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "pm7325_sdm_skin_therm";
> +	};
> +
> +	channel@147 {
> +		reg = <PM7325_ADC7_AMUX_THM4_100K_PU>;
> +		qcom,ratiometric;
> +		qcom,hw-settle-time = <200>;
> +		qcom,pre-scaling = <1 1>;
> +		label = "pm7325_wide_rfc_therm";
> +	};
> +};
> +
> +&pon_pwrkey {
> +	status = "okay";
> +};
> +
> +&pon_resin {
> +	linux,code = <KEY_VOLUMEDOWN>;
> +	status = "okay";
> +};
> +
> +&qup_spi13_cs {
> +	drive-strength = <6>;
> +	bias-disable;
> +};
> +
> +&qup_spi13_data_clk {
> +	drive-strength = <6>;
> +	bias-disable;
> +};
> +
> +&qup_uart5_rx {
> +	drive-strength = <2>;
> +	bias-disable;
> +};
> +
> +&qup_uart5_tx {
> +	drive-strength = <2>;
> +	bias-disable;
> +};
> +
> +&qupv3_id_0 {
> +	status = "okay";
> +};
> +
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
> +&remoteproc_adsp {
> +	firmware-name = "qcom/qcm6490/SHIFT/otter/adsp.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> +	firmware-name = "qcom/qcm6490/SHIFT/otter/cdsp.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_mpss {
> +	firmware-name = "qcom/qcm6490/SHIFT/otter/modem.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_wpss {
> +	firmware-name = "qcom/qcm6490/SHIFT/otter/wpss.mbn";
> +	/*
> +	 * FIXME: wpss remoteproc crashes during boot with:
> +	 * qcom_q6v5_pas 8a00000.remoteproc: fatal error received:
> +	 *   cmnos_thread.c:4645:Asserted in
> +	 *   cmnos_allocram.c:cmnos_allocram_base_with_alignment_recurse:497
> +	 *   with Args:0x3,0x3,0x0
> +	 */
> +	 status = "disabled";
> +};
> +
> +&sdc2_clk {
> +	drive-strength = <16>;
> +	bias-disable;
> +};
> +
> +&sdc2_cmd {
> +	drive-strength = <10>;
> +	bias-pull-up;
> +};
> +
> +&sdc2_data {
> +	drive-strength = <10>;
> +	bias-pull-up;
> +};
> +
> +&sdhc_2 {
> +	vmmc-supply = <&vreg_l9c>;
> +	vqmmc-supply = <&vreg_l6c>;
> +
> +	pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>;
> +	pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>;
> +
> +	status = "okay";
> +};
> +
> +&tlmm {
> +	/*
> +	* 48-52: protected by XPU, not sure why.
> +	*/
> +	gpio-reserved-ranges = <48 4>;

If they really shouldn't be protected from firmware level (fingerprint
reader or whatnot), somebody at SHIFT should patch TZ firmware and
change the owner from TZ to HLOS.

> +
> +	bluetooth_enable_default: bluetooth-enable-default-state {
> +		pins = "gpio85";
> +		function = "gpio";
> +		output-low;
> +		bias-disable;
> +	};
> +
> +	qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
> +		pins = "gpio28";
> +		function = "gpio";
> +		/*
> +		* Configure a bias-bus-hold on CTS to lower power
> +		* usage when Bluetooth is turned off. Bus hold will
> +		* maintain a low power state regardless of whether
> +		* the Bluetooth module drives the pin in either
> +		* direction or leaves the pin fully unpowered.
> +		*/
> +		bias-bus-hold;
> +	};
> +
> +	qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
> +		pins = "gpio29";
> +		function = "gpio";
> +		/*
> +		* Configure pull-down on RTS. As RTS is active low
> +		* signal, pull it low to indicate the BT SoC that it
> +		* can wakeup the system anytime from suspend state by
> +		* pulling RX low (by sending wakeup bytes).
> +		*/
> +		bias-pull-down;
> +	};
> +
> +	qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
> +		pins = "gpio30";
> +		function = "gpio";
> +		/*
> +		* Configure pull-up on TX when it isn't actively driven
> +		* to prevent BT SoC from receiving garbage during sleep.
> +		*/
> +		bias-pull-up;
> +	};
> +
> +	qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
> +		pins = "gpio31";
> +		function = "gpio";
> +		/*
> +		* Configure a pull-up on RX. This is needed to avoid
> +		* garbage data when the TX pin of the Bluetooth module
> +		* is floating which may cause spurious wakeups.
> +		*/
> +		bias-pull-up;
> +	};
> +
> +	sw_ctrl_default: sw-ctrl-default-state {
> +		pins = "gpio86";
> +		function = "gpio";
> +		bias-pull-down;
> +	};
> +};
> +
> +&uart5 {
> +	compatible = "qcom,geni-debug-uart";

This should be redundant soon if the author resends anytime soon

https://lore.kernel.org/linux-arm-msm/20240416105650.2626-1-quic_vdadhani@quicinc.com/

Don't see anything wrong with the rest

Regards
Luca

> +	status = "okay";
> +};
> +
> +&uart7 {
> +	/delete-property/interrupts;
> +	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
> +			<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
> +
> +	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
> +	pinctrl-names = "default", "sleep";
> +
> +	status = "okay";
> +
> +	bluetooth: bluetooth {
> +		compatible = "qcom,wcn6750-bt";
> +
> +		pinctrl-0 = <&bluetooth_enable_default>, <&sw_ctrl_default>;
> +		pinctrl-names = "default";
> +
> +		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
> +		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
> +
> +		vddio-supply = <&vreg_l19b>;
> +		vddaon-supply = <&vreg_s7b>;
> +		vddbtcxmx-supply = <&vreg_s7b>;
> +		vddrfacmn-supply = <&vreg_s7b>;
> +		vddrfa0p8-supply = <&vreg_s7b>;
> +		vddrfa1p7-supply = <&vreg_s1b>;
> +		vddrfa1p2-supply = <&vreg_s8b>;
> +		vddrfa2p2-supply = <&vreg_s1c>;
> +		vddasd-supply = <&vreg_l11c>;
> +
> +		max-speed = <3200000>;
> +	};
> +};
> +
> +&ufs_mem_hc {
> +	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
> +
> +	vcc-supply = <&vreg_l7b>;
> +	vcc-max-microamp = <800000>;
> +	/*
> +	* Technically l9b enables an eLDO (supplied by s1b) which then powers
> +	* VCCQ2 of the UFS.
> +	*/
> +	vccq-supply = <&vreg_l9b>;
> +	vccq-max-microamp = <900000>;
> +
> +	status = "okay";
> +};
> +
> +&ufs_mem_phy {
> +	vdda-phy-supply = <&vreg_l10c>;
> +	vdda-pll-supply = <&vreg_l6b>;
> +
> +	status = "okay";
> +};
> +
> +&usb_1 {
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +	dr_mode = "otg";
> +	usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> +	remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_dp_qmpphy_out {
> +	remote-endpoint = <&pmic_glink_ss_in>;
> +};
> +
> +&usb_1_hsphy {
> +	vdda-pll-supply = <&vreg_l10c>;
> +	vdda18-supply = <&vreg_l1c>;
> +	vdda33-supply = <&vreg_l2b>;
> +
> +	qcom,hs-crossover-voltage-microvolt = <28000>;
> +	qcom,hs-output-impedance-micro-ohms = <2600000>;
> +	qcom,hs-rise-fall-time-bp = <5430>;
> +	qcom,hs-disconnect-bp = <1743>;
> +	qcom,hs-amplitude-bp = <2430>;
> +
> +	qcom,pre-emphasis-amplitude-bp = <20000>;
> +	qcom,pre-emphasis-duration-bp = <20000>;
> +
> +	qcom,squelch-detector-bp = <(-2090)>;
> +
> +	orientation-switch;
> +
> +	status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> +	vdda-phy-supply = <&vreg_l6b>;
> +	vdda-pll-supply = <&vreg_l1b>;
> +
> +	status = "okay";
> +};
> +
> +&wifi {
> +	qcom,ath11k-calibration-variant = "SHIFTphone_8";
> +
> +	/* FIXME: wpss remoteproc crashes during init */
> +	status = "disabled";
> +};
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..678e800ac797 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -92,8 +92,9 @@  dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-fairphone-fp5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-idp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-shift-otter.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qdu1000-idp.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
new file mode 100644
index 000000000000..ceef8b9b2414
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts
@@ -0,0 +1,938 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Based largely on Fairphone 5 DT.
+ *
+ * Copyright (c) 2023, Luca Weiss <luca.weiss@fairphone.com>
+ * Copyright (c) 2024, Caleb Connolly <caleb.connolly@linaro.org>
+ */
+
+/dts-v1/;
+
+#define PM7250B_SID 8
+#define PM7250B_SID1 9
+
+#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sc7280.dtsi"
+#include "pmk8350.dtsi" /* PMK7325 */
+#include "pm7325.dtsi"
+#include "pm8350c.dtsi"
+#include "pm7250b.dtsi"
+
+/* There is also a pmr735a */
+
+/delete-node/ &rmtfs_mem;
+
+/ {
+	model = "SHIFT SHIFTphone 8";
+	compatible = "shift,otter", "qcom,qcm6490";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart7;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0:115200n8";
+
+		framebuffer0: framebuffer@a000000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0xe1000000 0x0 (2400 * 1080 * 4)>;
+			width = <1080>;
+			height = <2400>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+			clocks = <&gcc GCC_DISP_HF_AXI_CLK>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&volume_down_default>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume up";
+			gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_dp_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&fsa4480_sbu_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		cont_splash_mem: cont-splash@e1000000 {
+			reg = <0x0 0xe1000000 0x0 0x2300000>;
+			no-map;
+		};
+
+		cdsp_mem: cdsp@88f00000 {
+			reg = <0x0 0x88f00000 0x0 0x1e00000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f8500000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0xf8500000 0x0 0x600000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>, <QCOM_SCM_VMID_NAV>;
+		};
+	};
+
+	thermal-zones {
+		camera-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmk8350_adc_tm 2>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		chg-skin-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm7250b_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		conn-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm7250b_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		quiet-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmk8350_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		rear-cam-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmk8350_adc_tm 4>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		sdm-skin-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmk8350_adc_tm 3>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		xo-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmk8350_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm7325-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vreg_s1b: smps1 {
+			regulator-min-microvolt = <1840000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7b: smps7 {
+			regulator-min-microvolt = <535000>;
+			regulator-max-microvolt = <1120000>;
+		};
+
+		vreg_s8b: smps8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
+		};
+
+		vreg_l1b: ldo1 {
+			regulator-min-microvolt = <825000>;
+			regulator-max-microvolt = <925000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b: ldo2 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b: ldo3 {
+			regulator-min-microvolt = <312000>;
+			regulator-max-microvolt = <910000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b: ldo6 {
+			regulator-min-microvolt = <1140000>;
+			regulator-max-microvolt = <1260000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b: ldo7 {
+			/* Constrained for UFS VCC, at least until UFS driver scales voltage */
+			regulator-min-microvolt = <2952000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b: ldo8 {
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b: ldo9 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b: ldo11 {
+			regulator-min-microvolt = <1504000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b: ldo12 {
+			regulator-min-microvolt = <751000>;
+			regulator-max-microvolt = <824000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b: ldo13 {
+			regulator-min-microvolt = <530000>;
+			regulator-max-microvolt = <824000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b: ldo14 {
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b: ldo15 {
+			regulator-min-microvolt = <765000>;
+			regulator-max-microvolt = <1020000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b: ldo16 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b: ldo17 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18b: ldo18 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19b: ldo19 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s1c: smps1 {
+			regulator-min-microvolt = <2190000>;
+			regulator-max-microvolt = <2210000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s9c: smps9 {
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c: ldo1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c: ldo3 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5c: ldo5 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c: ldo8 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c: ldo9 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c: ldo10 {
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c: ldo11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c: ldo12 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c: ldo13 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+&gcc {
+	protected-clocks = <GCC_CFG_NOC_LPASS_CLK>,
+			<GCC_EDP_CLKREF_EN>,
+			<GCC_MSS_CFG_AHB_CLK>,
+			<GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>,
+			<GCC_MSS_OFFLINE_AXI_CLK>,
+			<GCC_MSS_Q6SS_BOOT_CLK_SRC>,
+			<GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+			<GCC_MSS_SNOC_AXI_CLK>,
+			<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			<GCC_QSPI_CORE_CLK>,
+			<GCC_QSPI_CORE_CLK_SRC>,
+			<GCC_SEC_CTRL_CLK_SRC>,
+			<GCC_WPSS_AHB_BDG_MST_CLK>,
+			<GCC_WPSS_AHB_CLK>,
+			<GCC_WPSS_RSCP_CLK>;
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/qcm6490/SHIFT/otter/a660_zap.mbn";
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* PM8008 PMIC @ 8 and 9 */
+	/* rtc6226 FM receiver @ 64 */
+
+	typec-mux@42 {
+		compatible = "fcs,fsa4480";
+		reg = <0x42>;
+
+		vcc-supply = <&vreg_bob>;
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_sbu>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	/* tas2563 audio codec @ 4d */
+};
+
+&i2c9 {
+	status = "okay";
+
+	/* TMS(?) NFC @ 28 */
+	/* Ti drv2624 haptics @ 5a */
+};
+
+&i2c13 {
+	status = "okay";
+
+	/* focaltech FT3658U @ 38 */
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/qcm6490/SHIFT/otter/ipa_fws.mbn";
+	status = "okay";
+};
+
+&pm7250b_adc {
+	channel@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "charger_skin_therm";
+	};
+
+	channel@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "conn_therm";
+	};
+};
+
+&pm7250b_adc_tm {
+	status = "okay";
+
+	charger-skin-therm@0 {
+		reg = <0>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	conn-therm@1 {
+		reg = <1>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm7325_gpios {
+	volume_down_default: volume-down-default-state {
+		pins = "gpio6";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pmk8350_adc_tm {
+	status = "okay";
+
+	xo-therm@0 {
+		reg = <0>;
+		io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	quiet-therm@1 {
+		reg = <1>;
+		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	cam-flash-therm@2 {
+		reg = <2>;
+		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	sdm-skin-therm@3 {
+		reg = <3>;
+		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	wide-rfc-therm@4 {
+		reg = <4>;
+		io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&pmk8350_vadc {
+	status = "okay";
+
+	channel@44 {
+		reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "pmk8350_xo_therm";
+	};
+
+	channel@144 {
+		reg = <PM7325_ADC7_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "pm7325_quiet_therm";
+	};
+
+	channel@145 {
+		reg = <PM7325_ADC7_AMUX_THM2_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "pm7325_cam_flash_therm";
+	};
+
+	channel@146 {
+		reg = <PM7325_ADC7_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "pm7325_sdm_skin_therm";
+	};
+
+	channel@147 {
+		reg = <PM7325_ADC7_AMUX_THM4_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "pm7325_wide_rfc_therm";
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&qup_spi13_cs {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&qup_spi13_data_clk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/qcm6490/SHIFT/otter/adsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/qcm6490/SHIFT/otter/cdsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/qcm6490/SHIFT/otter/modem.mbn";
+	status = "okay";
+};
+
+&remoteproc_wpss {
+	firmware-name = "qcom/qcm6490/SHIFT/otter/wpss.mbn";
+	/*
+	 * FIXME: wpss remoteproc crashes during boot with:
+	 * qcom_q6v5_pas 8a00000.remoteproc: fatal error received:
+	 *   cmnos_thread.c:4645:Asserted in
+	 *   cmnos_allocram.c:cmnos_allocram_base_with_alignment_recurse:497
+	 *   with Args:0x3,0x3,0x0
+	 */
+	 status = "disabled";
+};
+
+&sdc2_clk {
+	drive-strength = <16>;
+	bias-disable;
+};
+
+&sdc2_cmd {
+	drive-strength = <10>;
+	bias-pull-up;
+};
+
+&sdc2_data {
+	drive-strength = <10>;
+	bias-pull-up;
+};
+
+&sdhc_2 {
+	vmmc-supply = <&vreg_l9c>;
+	vqmmc-supply = <&vreg_l6c>;
+
+	pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>;
+	pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>;
+
+	status = "okay";
+};
+
+&tlmm {
+	/*
+	* 48-52: protected by XPU, not sure why.
+	*/
+	gpio-reserved-ranges = <48 4>;
+
+	bluetooth_enable_default: bluetooth-enable-default-state {
+		pins = "gpio85";
+		function = "gpio";
+		output-low;
+		bias-disable;
+	};
+
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		* Configure a bias-bus-hold on CTS to lower power
+		* usage when Bluetooth is turned off. Bus hold will
+		* maintain a low power state regardless of whether
+		* the Bluetooth module drives the pin in either
+		* direction or leaves the pin fully unpowered.
+		*/
+		bias-bus-hold;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		* Configure pull-down on RTS. As RTS is active low
+		* signal, pull it low to indicate the BT SoC that it
+		* can wakeup the system anytime from suspend state by
+		* pulling RX low (by sending wakeup bytes).
+		*/
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		* Configure pull-up on TX when it isn't actively driven
+		* to prevent BT SoC from receiving garbage during sleep.
+		*/
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		* Configure a pull-up on RX. This is needed to avoid
+		* garbage data when the TX pin of the Bluetooth module
+		* is floating which may cause spurious wakeups.
+		*/
+		bias-pull-up;
+	};
+
+	sw_ctrl_default: sw-ctrl-default-state {
+		pins = "gpio86";
+		function = "gpio";
+		bias-pull-down;
+	};
+};
+
+&uart5 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+&uart7 {
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+			<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+
+	bluetooth: bluetooth {
+		compatible = "qcom,wcn6750-bt";
+
+		pinctrl-0 = <&bluetooth_enable_default>, <&sw_ctrl_default>;
+		pinctrl-names = "default";
+
+		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+
+		vddio-supply = <&vreg_l19b>;
+		vddaon-supply = <&vreg_s7b>;
+		vddbtcxmx-supply = <&vreg_s7b>;
+		vddrfacmn-supply = <&vreg_s7b>;
+		vddrfa0p8-supply = <&vreg_s7b>;
+		vddrfa1p7-supply = <&vreg_s1b>;
+		vddrfa1p2-supply = <&vreg_s8b>;
+		vddrfa2p2-supply = <&vreg_s1c>;
+		vddasd-supply = <&vreg_l11c>;
+
+		max-speed = <3200000>;
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7b>;
+	vcc-max-microamp = <800000>;
+	/*
+	* Technically l9b enables an eLDO (supplied by s1b) which then powers
+	* VCCQ2 of the UFS.
+	*/
+	vccq-supply = <&vreg_l9b>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l10c>;
+	vdda-pll-supply = <&vreg_l6b>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l10c>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l2b>;
+
+	qcom,hs-crossover-voltage-microvolt = <28000>;
+	qcom,hs-output-impedance-micro-ohms = <2600000>;
+	qcom,hs-rise-fall-time-bp = <5430>;
+	qcom,hs-disconnect-bp = <1743>;
+	qcom,hs-amplitude-bp = <2430>;
+
+	qcom,pre-emphasis-amplitude-bp = <20000>;
+	qcom,pre-emphasis-duration-bp = <20000>;
+
+	qcom,squelch-detector-bp = <(-2090)>;
+
+	orientation-switch;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l6b>;
+	vdda-pll-supply = <&vreg_l1b>;
+
+	status = "okay";
+};
+
+&wifi {
+	qcom,ath11k-calibration-variant = "SHIFTphone_8";
+
+	/* FIXME: wpss remoteproc crashes during init */
+	status = "disabled";
+};