diff mbox series

[2/3] arm64: dts: qcom: sdx75: Add SDHCI node

Message ID 20240515120958.32032-3-quic_nainmeht@quicinc.com
State Superseded
Headers show
Series Add SDHCI support for SDX75 SoC | expand

Commit Message

Naina Mehta May 15, 2024, 12:09 p.m. UTC
Add sdhc node for SDX75 SoC to support SD card.
Also add pins required for SDHCI.

Signed-off-by: Naina Mehta <quic_nainmeht@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sdx75.dtsi | 89 +++++++++++++++++++++++++++++
 1 file changed, 89 insertions(+)

--
2.17.1
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdx75.dtsi b/arch/arm64/boot/dts/qcom/sdx75.dtsi
index da1704061d58..9723b716f02e 100644
--- a/arch/arm64/boot/dts/qcom/sdx75.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdx75.dtsi
@@ -8,6 +8,7 @@ 

 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,sdx75-gcc.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,icc.h>
 #include <dt-bindings/interconnect/qcom,sdx75.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -538,6 +539,54 @@ 
 			#hwlock-cells = <1>;
 		};

+		sdhc: mmc@8804000 {
+			compatible = "qcom,sdx75-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x0 0x08804000 0x0 0x1000>;
+
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq",
+					  "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
+			iommus = <&apps_smmu 0x00a0 0x0>;
+			qcom,dll-config = <0x0007442c>;
+			qcom,ddr-config = <0x80040868>;
+			power-domains = <&rpmhpd RPMHPD_CX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+
+			interconnects = <&system_noc MASTER_SDCC_1 &mc_virt SLAVE_EBI1>,
+					<&gem_noc MASTER_APPSS_PROC &system_noc SLAVE_SDCC_1>;
+			interconnect-names = "sdhc-ddr",
+					     "cpu-sdhc";
+			bus-width = <4>;
+			dma-coherent;
+
+			/* Forbid SDR104/SDR50 - broken hw! */
+			sdhci-caps-mask = <0x3 0>;
+
+			status = "disabled";
+
+			sdhc1_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+			};
+		};
+
 		usb: usb@a6f8800 {
 			compatible = "qcom,sdx75-dwc3", "qcom,dwc3";
 			reg = <0x0 0x0a6f8800 0x0 0x400>;
@@ -683,6 +732,46 @@ 
 				drive-strength = <2>;
 				bias-pull-down;
 			};
+
+			sdc1_default: sdc1-default-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdc1_sleep: sdc1-sleep-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
 		};

 		apps_smmu: iommu@15000000 {